Singcall SC-R15 - User Manual

Manual for Small Receiver
 Call button registering
1) Standby mode, keep pressing key (FUN) 3 seconds till [F1] appears on the screen.
2) Press key (ENT), the biggest registered number ([xx.]、[xxx.])appears on screen ,if
there is no registered number, then [01] or [001] appears.
3) Press (UP),(MOVE),(DOWN) to choose the registered number wanted, the radix
point behind the chose number lights means the number has been registered and
can not registered again. Press key (ENT) to delete this number (after deleting, the
radix point is not light), then you can register the number again.
4) Press the call button to be registered, the number flashes on screen with music
prompt, adding 1 automatically and then stops.
5) Press key (ESC), and[ F1] appears.
6) Press key (ESC) again, back to standby mode. The registration is finished.
7) Repeat step3）～ 4）to register all the call buttons you need, and then press key (ESC)
twice, back to standby mode. Registration finished.
 Prompt music setting
1) Standby mode, press key (FUN) 3 seconds till [F1] appears on the screen.
2) Use key (UP) to choose [F2].
3) Press key (ENT) and (01) appears.
4) Use the key (UP),(DOWN) to choose prompt music.01 means the music
“Dingdong”,02 means “alarming sound” and 00 means “voice report”.
5)Press key (ENT), and [F2] appears.
6）Press key (ESC) and back to standby mode. Prompt setting is done.
 Display time setting for the call button numbers
1) Standby mode, press key (FUN) 3 seconds till [F1] appears on the screen.
2) Use key(UP)to choose [F3].
3) Press key (ENT), and [20] appears on the screen.
4) Use key (UP),(DOWN) to choose the display time wanted.(00)means unlimited
display, the figure of 01-99 means the corresponding display time from 1-99 seconds.
5) Press key (ENT), and [F3] appears.
6) Press key (ESC) and back to standby mode. The setting is done.
 Prompt music length setting
1) Standby mode, press key (FUN) 3 seconds and [F1] appears on the screen.
2) Use key (UP)to choose [F4].
3) Press key (ENT), and [01] appears on the screen.
4)Use key (UP),(DOWN) to choose the prompt music length and voice report times
wanted, number 01-15 means 15 kinds of the length, one figure means the prompt
length is 2 seconds, then 15 means the prompt length is 30 seconds. 01-15 also means
the frequency of voice report is 01-15 times.

Summary

Call Button Registering

Enter Standby Mode and Initiate Registration

Keep pressing FUN for 3 seconds until [F1] appears, then press ENT to view the registered number.

Select and Delete Registered Numbers

Use UP/MOVE/DOWN to select a number. The radix point indicates registration. Press ENT to delete.

Perform Call Button Registration

Press the call button; the number flashes with music prompt, auto-incrementing.

Exit Registration Mode

Press ESC to return to [F1] or standby mode. Repeat steps for multiple registrations.

Prompt Music Setting

Access Prompt Music Menu

From standby mode, press FUN for 3 seconds until [F1] appears, then use UP to select [F2].

Select and Confirm Prompt Music

Press ENT to show '01'. Use UP/DOWN to select music (01: Dingdong, 02: Alarming, 00: Voice report).

Display Time Setting for Call Button Numbers

Access Display Time Menu

From standby mode, press FUN for 3 seconds until [F1] appears, then use UP to select [F3].

Set Display Time Duration

Press ENT to show '20'. Use UP/DOWN to choose display time (00: unlimited, 01-99: seconds).

Prompt Music Length Setting

Access Music Length Menu

From standby mode, press FUN for 3 seconds until [F1] appears, then use UP to select [F4].

Configure Music Length and Voice Report Times

Press ENT to show '01'. Use UP/DOWN for length (01-15: 2-30s) or voice report times (01-15).

Number Display Mode Setting

Access Display Mode Menu

From standby mode, press FUN for 3 seconds until [F1] appears, then use UP to select [F5].

Select Display Mode Type

Press ENT to show '01'. Use UP/MOVE/DOWN to choose mode (01-10: digital, 11-20: alphanumeric).

Deleting Registered Numbers and Initializing

Access Deletion;Initialization Menu

From standby mode, press FUN for 3 seconds until [F1] appears, then use UP to select [F6].

Delete Specific Registered Number

Press ENT for min number. Use UP/MOVE/DOWN to select number, press ENT to delete.

Initialize Receiver

Keep pressing ENT to show '---', then '[00]'/'[000]' to complete initialization.

Exit Deletion;Initialization Mode

Press ESC to return to [F6] or standby mode. The operation is completed.

Overview

1. Call Button Registering
2. Prompt Music Setting
3. Display Time Setting for Call Button Numbers
4. Prompt Music Length Setting
5. Number Display Mode Setting (Not suitable for receiver SC-R10)
6. Deleting Registered Number or Initializing the Receiver

This document outlines the operational procedures for a small receiver, covering various settings and maintenance functions.

Call Button Registering

Function Description: This feature allows the user to register call buttons with the receiver, enabling the device to recognize and respond to specific call signals.

Usage Features:

1. Initiation: To begin the registration process, the user must press and hold the FUN key for 3 seconds until [F1] is displayed on the screen.
2. Accessing Registration Mode: Pressing the ENT key will show the largest registered number. If no numbers are registered, [01] or [001] will appear.
3. Selecting a Number: The UP, MOVE, or DOWN keys are used to navigate and select a desired registration number. A lit radix point next to the chosen number indicates that it is already registered and cannot be re-registered.
4. Deleting a Registered Number (for re-registration): If a number is already registered, pressing the ENT key will delete it, extinguishing the radix point and making it available for re-registration.
5. Registering a Call Button: Once a number is selected and available, pressing the physical call button to be registered will cause the number on the screen to flash, accompanied by a musical prompt. The number will automatically increment by one and then stop, indicating successful registration.
6. Exiting Registration Mode: Pressing the ESC key will display [F1]. Pressing ESC again will return the receiver to standby mode, completing the registration of the current button.
7. Batch Registration: Steps 3 through 4 can be repeated to register multiple call buttons. After all desired buttons are registered, pressing the ESC key twice will return the device to standby mode, finalizing the entire registration process.

Prompt Music Setting

Function Description: This feature allows the user to customize the type of music or sound played when a call button is triggered.

Usage Features:

1. Initiation: Press and hold the FUN key for 3 seconds until [F1] appears on the screen.
2. Accessing Music Setting: Use the UP key to select [F2].
3. Entering Selection Mode: Press the ENT key, and (01) will appear.
4. Choosing Prompt Music: The UP and DOWN keys are used to select the desired prompt music:
   • 01 corresponds to the "Dingdong" sound.
   • 02 corresponds to an "alarming sound."
   • 00 corresponds to a "voice report."
5. Saving Selection: Press the ENT key, and [F2] will appear.
6. Exiting Setting Mode: Press the ESC key to return to standby mode. The prompt music setting is now complete.

Display Time Setting for Call Button Numbers

Function Description: This feature enables the user to set how long a call button's number remains displayed on the screen after being triggered.

Usage Features:

1. Initiation: Press and hold the FUN key for 3 seconds until [F1] appears on the screen.
2. Accessing Display Time Setting: Use the UP key to select [F3].
3. Entering Selection Mode: Press the ENT key, and [20] will appear on the screen.
4. Choosing Display Time: The UP and DOWN keys are used to select the desired display time:
   • 00 signifies unlimited display time.
   • Figures from 01 to 99 correspond to a display time of 1 to 99 seconds, respectively.
5. Saving Selection: Press the ENT key, and [F3] will appear.
6. Exiting Setting Mode: Press the ESC key to return to standby mode. The display time setting is now complete.

Prompt Music Length Setting

Function Description: This feature allows the user to adjust the duration of the prompt music or the frequency of voice reports.

Usage Features:

1. Initiation: Press and hold the FUN key for 3 seconds until [F1] appears on the screen.
2. Accessing Length Setting: Use the UP key to select [F4].
3. Entering Selection Mode: Press the ENT key, and [01] will appear on the screen.
4. Choosing Length/Frequency: The UP and DOWN keys are used to select the desired prompt music length or voice report frequency:
   • Numbers 01 to 15 represent 15 different lengths.
   • A single figure (e.g., 01) indicates a prompt length of 2 seconds.
   • 15 indicates a prompt length of 30 seconds.
   • 01 to 15 also correspond to the frequency of voice reports (1 to 15 times).
5. Saving Selection: Press the ENT key, and [F4] will appear.
6. Exiting Setting Mode: Press the ESC key to return to standby mode. The setting is now complete.

Number Display Mode Setting (Not suitable for receiver SC-R10)

Function Description: This feature allows the user to choose between an all-digital display or a display that includes English letters for numbers. This setting is specifically noted as not suitable for the SC-R10 receiver model.

Usage Features:

1. Initiation: Press and hold the FUN key for 3 seconds until [F1] appears on the screen.
2. Accessing Display Mode Setting: Use the UP key to select [F5].
3. Entering Selection Mode: Press the ENT key, and [01] will appear.
4. Choosing Display Mode: The UP, MOVE, or DOWN keys are used to select the desired display mode:
   • 01 to 10 represent an all-digital display (default setting).
   • 11 to 20 represent digits beginning with an English letter (the letters are A, B, C, D, E, F, H, P, J, L).
5. Saving Selection: Press the ENT key, and [F5] will appear.
6. Exiting Setting Mode: Press the ESC key to return to standby mode. The setting is now complete.

Deleting Registered Number or Initializing the Receiver

Function Description: This feature provides the capability to delete individual registered numbers or to perform a full initialization of the receiver, clearing all registered data.

Usage Features:

1. Initiation: Press and hold the FUN key for 3 seconds until [F1] appears on the screen.
2. Accessing Deletion/Initialization Mode: Use the UP key to select [F6].
3. Entering Selection Mode: Press the ENT key, and the registered minimum number will appear.
4. Choosing Number to Delete: The UP, MOVE, or DOWN keys are used to select the specific number to be deleted.
5. Deleting a Number: Pressing the ENT key will cause the selected number to flash and then be deleted, accompanied by prompt music. The next registered number will then appear on the screen.
6. Initializing the Receiver (Factory Reset): To initialize the receiver, continue pressing the ENT key. "---" will appear on the screen, followed by [00] and then [000], indicating that the initialization process is complete.
7. Exiting Deletion/Initialization Mode: Press the ESC key, and [F6] will appear again. Press ESC one more time to return to standby mode. The number deletion or initialization process is now complete.

Singcall SC-R15 Specifications

General

Model	SC-R15
Battery	Rechargeable Lithium Battery
Dimensions	110 x 60 x 25 mm
Weight	150g
Notification Types	Vibration, LED, Sound
Working Frequency	433MHz
Output Power	≤ 10mW
Type	Receiver
Working voltage	3.7V
Working current	50mA
Frequency Range	433MHz