12
! prior to disposal protect battery terminals with
heavy tape to prevent short-circuit
Only for UK countries
• Do not dispose of electric tools, accessories and
packaging together with household waste material
- in observance of on Waste Electric and Electronic
Equipment Regulations 2013 (SI 2013/3113), electric
tools that have reached the end of their life must be
collected separately and returned to an environmentally
compatible recycling facility
- symbol 6 will remind you of this when the need for
disposing occurs
! prior to disposal protect battery terminals with
heavy tape to prevent short-circuit
NOISE / VIBRATION
• Measured in accordance with EN 62841 the sound
pressure level of this tool is 76 dB(A) and the sound
power level 84 dB(A) (uncertainty
K = 5 dB), and the vibration <2.5 m/s² (triax vector sum;
uncertainty K = 1.5 m/s²)
• The vibration emission level has been measured in
accordance with a standardised test given in EN 62841;
it may be used to compare one tool with another and as
a preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
-
increase the exposure level
-
reduce the exposure level
!
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work
patterns
b
sans brosse
3080
INTRODUCTION
• Cet outil est destiné au serrage et au desserrage des vis
et au perçage dans le bois, le métal, la céramique et le
plastique.
• Cet outil n’est pas conçu pour un usage professionnel.
• Lisez et conservez ce mode d’emploi.3
DONNÉES TECHNIQUES 1
Couple max. pour vissage dans des matériaux durs selon
ISO 5393 : 130 Nm
PIÈCES DE L’OUTIL 2
A Interrupteur de marche/arrêt et réglage de vitesse
B Anneau pour réglage du couple
C Position de verrouillage (embrayage)
D Commutateur de vitesse
E
F Commutateur pour inverser le sens de rotation
preference and comfort. Loosen or fasten the auxiliary
handle as shown y
- keep ventilation slots E 2 uncovered
- do not apply too much pressure on the tool; let the tool
do the work for you
•
technology) gives the user greater control over the power
that do not have Anti-kickback brake technology.
-
rotates around the drilling axis.
-
and then press it again.
APPLICATION ADVICE
• Use the appropriate bits u
! only use sharp bits
• When drilling ferrous metals
- pre-drill a smaller hole, when a large hole is required
- lubricate drill bit occasionally with oil
• When turning in a screw at/near the cross cut end or an
edge of wood, pre-drill a hole in order to avoid cracking
• of the wood
•
screw is required, especially while removing
• When screwdriving in hard wood one should pre-drill a
hole
• Splinterfree drilling in wood i
•
MAINTENANCE / SERVICE
• This tool is not intended for professional use
• Always keep tool clean (especially ventilation slots E 2)
! remove battery from tool before cleaning
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL servic
send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of the
tool are listed on www.skil.com)
• Be aware that damage due to overload or improper
handling of the tool will be excluded from the warranty
(for the SKIL warranty conditions see www.skil.com or
ask your dealer)
ENVIRONMENT
Only for EU countries
• Do not dispose of electric tools, accessories and
packaging together with household waste material
- in observance of European Directive 2012/19/EC
on waste of electric and electronic equipment and
its implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 6 will remind you of this when the need for
disposing occurs
To Next Page
Loading...
