SKS Germany S-BOARD - User Manual

To Next Page

1a.

2a.

SW 2,5

GERMANY

MANUAL ¬ S-BOARD / S-BLADE SET ¬ 11512

ALLROAD ROAD

TYRE WIDTH

MAX.

EN. S-BOARD

Clip-on front mudguard for racing bikes, cyclocross bikes, hybrid bikes and gravel bikes, etc. for a max. tyre width of 38 mm. The S-BOARD is the ideal companion for

our S-BLADE rear mudguard. Its light, double-hinged quick release tting system also ts aero forks.

Mounting instructions: the S-BOARD is to be mounted on the fork so that there is a minimum clearance of 1.5 cm between the mudguard and the tyres all-round.

CAUTION! Only tighten the screws with max. 1 NM!

Initially position the mudguard on the fork so that the minimum clearance is adhered to in the upper Part A. This can be ascertained by pushing it up or down (Arrow

B). Now tighten the quick release bungee cord around the fork and hook it into the fastening so that it is unable to slip on the fork (see 1a.).

If necessary, protect the frame using the enclosed paintwork protection lm. It is possible to permanently mount the mudguards using cable binders (see under

»Permanent mounting of the mudguards«)

Now adjust the wheel protection by loosening the screws and moving the mudguard in the longitudinal holes beneath it so that the clearance between the mudgu-

ards and the tyres is a min. of 1.5 cm all-round.

Now retighten the screws (max. 1 NM) so that the mudguard now rmly remains in position.

If necessary, carefully shorten the bungee cord using a pair of scissors so that the ends are unable to make contact with the wheel spokes.

Permanent mounting of the mudguards

In addition to using the quick release bungee cords, the S-BOARD can also be xed in place with cable binders (C). This type of mounting is only suitable for a per-

manent mounting and as protection against the S-BOARD being stolen from the bike. In order to mount the mudguard, use 2 cable binders per side in addition to the

bungee cords. Pull the cable binders as tight as possible in order to ensure that slipping is not possible. Carefully cut the protruding ends of the cable binders off with

a pair of scissors.

Safety instructions!

Ensure the correct positioning of the mudguards each time before you use the bike. A non-adherence of the minimum clearance between the mudguard and the tyre,

can result in damage being caused or as a worst case scenario, a fall is also possible. It is therefore imperative that you adhere to the minimum clearance of 1.5 cm

when mounting the mudguards. Ensure that the brakes work correctly and that the mudguards do not come into contact with the moving parts of the brakes. The

bungee cords are subject to natural ageing by UV radiation. Therefore inspect the condition of them at regular intervals and replace them in good time should they

show signs of damage.

Mountingvideo Youtube

WARNING! SKS is not responsible for damage to frame paint or carbon resulting from use of this product. Proper use of protection lm and maintenance, including

regular cleaning of frame and fender at attachment points, will prevent such damage.

Pintworkprotection

Allen max. 1 Nm!

Elongated eyelet

Need help?

Do you have a question about the SKS Germany S-BOARD and is the answer not in the manual?

Summary

S-BOARD Front Mudguard

S-BOARD Mounting Instructions

Detailed steps for attaching the S-BOARD mudguard to the fork, ensuring minimum clearance.

Permanent Mounting Method

Method for permanently fixing the mudguard using cable binders in addition to bungee cords.

S-BOARD Safety Instructions

Critical advice on correct positioning, minimum clearance, brake function, and bungee cord inspection.

S-BOARD User Warning

Disclaimer regarding frame paint or carbon damage from product use.

Overview

The S-BOARD / S-BLADE SET is a mudguard system designed for bicycles, offering protection from road spray and debris. This set includes a front mudguard, the S-BOARD, and a rear mudguard, the S-BLADE, both engineered for ease of use and compatibility with various bike types.

The S-BOARD is a clip-on front mudguard suitable for racing bikes, cyclocross bikes, hybrid bikes, and gravel bikes. Its primary function is to prevent water and mud from being thrown up by the front wheel, keeping the rider and the bike cleaner. A key usage feature of the S-BOARD is its light, double-hinged quick-release fitting system, which also accommodates aero forks. This system allows for quick attachment and removal, making it convenient for riders who may not always need a mudguard.

Installation of the S-BOARD involves positioning it on the fork, ensuring a minimum clearance of 1.5 cm between the mudguard and the tires all-round. This clearance is crucial for safe operation and to prevent damage. The mudguard is initially positioned to adhere to the minimum clearance in the upper part, which can be adjusted by pushing it up or down. Once the correct position is found, the quick-release bungee cord is tightened around the fork and hooked into its fastening, securing the mudguard in place and preventing it from slipping. For added protection, an enclosed paintwork protection film can be used to safeguard the frame. The S-BOARD also offers the option for permanent mounting using cable binders, providing an extra layer of security against theft and ensuring a more fixed attachment.

After the initial positioning, the wheel protection is adjusted by loosening screws and moving the mudguard in longitudinal holes beneath it. This step ensures that the 1.5 cm minimum clearance between the mudguards and the tires is maintained all-round. Once adjusted, the screws are retightened, but it's important to note that the maximum torque for tightening is 1 Nm. This precise tightening prevents over-tightening, which could damage the components. If the bungee cord is too long, it can be carefully shortened with scissors to prevent its ends from contacting the wheel spokes, which could interfere with the wheel's rotation or cause damage.

For permanent mounting, in addition to the quick-release bungee cords, the S-BOARD can be secured with two cable binders per side. These cable binders are pulled as tight as possible to prevent any slipping. The protruding ends of the cable binders are then cut off with scissors for a neat finish. This permanent mounting option is particularly useful for riders who consistently use their mudguards and wish to deter theft.

Maintenance features for the S-BOARD include regular checks of the mudguard's positioning before each ride to ensure the minimum clearance is maintained. Failure to adhere to this clearance can lead to damage or, in a worst-case scenario, a fall. It's also important to ensure that the brakes work correctly and that the mudguards do not interfere with the moving parts of the brakes. The bungee cords are subject to natural aging due to UV radiation, so their condition should be inspected regularly and replaced if any signs of damage are observed. Proper use of the protection film and regular cleaning of the frame and fender at attachment points are recommended to prevent damage to the frame paint or carbon components.

The S-BLADE is an extremely light rear wheel snap-on mudguard, manufactured from high-quality, impact-resistant, high-performance plastic. Its function is to protect the rider from spray and dirt coming off the rear wheel. The S-BLADE features an easy quick-release fastening system using a powerstrap, which is compatible with almost all seatposts. This design allows for quick and tool-free attachment and removal, similar to the S-BOARD, offering convenience and adaptability for different riding conditions. The powerstrap ensures a secure fit on the seatpost, preventing the mudguard from shifting during rides.

Overall, the S-BOARD / S-BLADE SET provides a comprehensive mudguard solution for various bicycle types, emphasizing ease of installation, adjustability, and durability, with clear guidelines for safe use and maintenance.