the green light will flashing. Meantime, turn on the main unit, can finish paring. Once successful paired, the green indicate
light will keep turning on.
2. Data link pin as illustrated, use attached wire or DIY connector to fight control board. Tx pin of receiver to Rx pin of Flight
control board.
Part 3: T10 Connect to Android phone
1. Connection between receiver and camera (example: mini digital camera), Power up the system. Please watch the video of
connection in www.skydroid.xin.
2. Please go to www.skydroid.xin to download the Skydroid FPV.
3. Using Bluetooth to connect the T10 and the display(Please check the part No. 1 ).
4. Click “Yes” to confrm then image will show on your phone.
5. Use of Skydroid FPV please go to the official website.
Part 4: How Tl0 connect to PC mission planner, QGC
1. Use two USB connectors cable to link between USB1 and USB port in PC. Select the port related to the ground station.
Please select Baud Rate 115200 to link with the data port of the fight controller. (QGC,mis- sionplanner need to add SDK of
Skydroid to show image, undevelopment).
Use Micro data cable to connect USB2 and PC, select baud rate 57600 (Only support data, not for video).
Part 5: How T1O to update firmware
1. Android update
Download and install Device Helper before upgrade.
2. T10 upgrade: connect T10 with the phone via Bluetooth, please check the part no.1. Turn of the main unit, press and
hold the button” A:; and longtime press the power button to turn it on, you will find button “A”‘s light flashing slowly,
which means, it is downloading. Meanwhile, open the Skydroid Device app to click “updating’; choosing update the
controller, and click “checking updating’; if there’s new firmware released, please click “update at once”.
3. R10 update: connect R10 with the phone via Bluetooth, please make sure the main unit is turning on and paired with
R10 (green indicate light turning on).
4. Open the Skydroid Device app to click “updating’; choosing update the receiver, and click” checking updating’; if there’s
new firmware released, please click” update at once”.
Part 6: Questions & Answers
Q: What is the Video/Data distance ofT10 in transmission?
A: Under an open area, the max distance of video link is 10km while data link is 20km.
Q: DoesT10 support ppm, sbus?
A: Yes! Sbus port is defaulted in the first row. If you need ppm signal which can be switched in Device Helper App.
Q: How to define two antenna on T10?
A: Two antenna are 2.4ghz redundant design. We use diversity technology so both antenna perform data link and
transmission.
Q: How to define two antenna on receiver?
A: Two antenna on Receiver are redundant design and telemetry.
Q: How to charge T10?
A: Use micro USB cable come with T10. Please use certified 5v charger. LED status:
LED fishing during charging and of when it is full.
Q: Where to watch demonstration video ofT10?
A: Please visit http://www.skydroid.xin and watch the video.
Q: How to power on/off the T10?
A: Short press and then long press the power switch.
Q: No LED indication on the receiver when plug into the fight control board?
A: T1O is power of; if the case still exist, check battery status(short press power switch to check the battery level), if not
binding, then bind it.
Q: How to change Mode?
A: Monitor system linked up with the radio by Bluetooth, then open Device Helper to select mode 1 or mode 2 and saved. No
need to set the others.
Q: How to calibrate neutral of the gimbal?
A: Calibration (watch video), please visit www.skydroid.xin.
Q: How many times of command being send out per second?
A: 300 times per second.
Q: Does T10 bind with new receiver?
To Next Page
Loading...