Need help?Do you have a question about the Skyrc Q200 and is the answer not in the manual?
General| Input Voltage | AC 100-240V / DC 11-18V |
|---|---|
| Balance Current | 300mA/cell |
| LiPo/LiFe/Lilon Cells | 1-6S |
| NiMH/NiCd Cells | 1-15S |
| Pb Battery Voltage | 2-20V |
| LiPo/LiFe/Lilon/LiHV Battery Cell Count | 1-6S |
| NiMH/NiCd Battery Cell Count | 1-15S |
| Charge Power | 200W |
| Charge Circuit Power | 200W |
| Charge Current Range | 0.1-10A |
| Discharge Current Range | 0.1-5A |
| Battery Types | LiPo, LiFe, LiIon, LiHV, NiMH, NiCd, Pb |
| Cell Count | LiPo/LiFe/Lilon/LiHV: 1-6S, NiMH/NiCd: 1-15S |
Charger supports simultaneous charging of 4 batteries with different chemistries.
Features a 3.5" color LCD display for a clean and intuitive user interface.
Supports AC/DC input and allows power distribution between channels in AC mode.
AUTO function prevents overcharging and malfunctions with two-way communication.
Stores up to 10 charge/discharge profiles per channel for quick recall.
Displays charge/discharge status and capacity percentage on screen.
Allows expert users to adjust the end voltage for charging.
Software for PC control, monitoring, and firmware updates.
Control the charger remotely via smartphone app using Bluetooth 4.0.
Built-in individual-cell balancer, no external balancer needed.
Supports LiPo, Lilon, LiFe, and the new LiHV battery series.
Allows charging LiHV batteries to a higher end voltage of 4.35V.
Special modes for faster charging or long-term battery storage.
Automatically peak-charges NiMH/NiCd batteries multiple times.
Automatic charge termination based on Delta-peak voltage detection.
Performs up to 5 cycles of charge/discharge for battery refreshing.
Set upper charging current limit for NiMH or NiCd batteries.
Check battery pack total voltage, highest, lowest, and individual cell voltages.
Measure battery's total internal resistance and each cell's resistance.
Automatically stops charging when a set capacity limit is reached.
Terminates process if battery temperature reaches the set limit.
Limits the maximum process time to avoid unforeseeable issues.
Charge phones and tablets using the built-in USB power output port.
Covers unattended operation, environmental hazards, and proper placement.
Details nominal voltage, max charge, storage, and discharge voltages.
Lists batteries and situations that should not be charged or discharged.
Ensures correct program, current, voltage, and secure connections.
Proper discharging procedures and warnings for lithium batteries.
Explains memory effect in NiCd and NiMH batteries.
Compliance information regarding FCC rules and radio frequency interference.
Details AC 100-240V and DC 11-18V power source connections.
Instructions for connecting LiPo, NiMH/NiCd, and Pb batteries using adapters.
Explains power distribution settings and operation in AC mode.
Details connection and requirements for DC power supply operation.
Explains programming menu and two ways to set up the charger.
Step-by-step flowchart for manually setting LiPo battery programs.
Details battery check, status monitor, completion, and stopping the process.
Explains various real-time information displayed during charging/discharging.
Guides on selecting NiMH/NiCd type and available charge modes.
Details on setting current and starting the standard NiMH/NiCd charge.
Automatic detection and charging for NiMH/NiCd batteries.
Steps to operate the automatic charge mode for NiMH/NiCd batteries.
Instructions for setting discharge rate and voltage cut-off.
Details the re-peak function for enhancing NiMH/NiCd battery performance.
Explains the charge/discharge cycling process for battery performance.
Suitable for 2-20V Pb batteries; low current charging is essential.
Setting charge rate to 1/10th of capacity for Pb batteries.
Setting discharge rate and voltage for Pb batteries.
Displays information like capacity cut-off, safety timer, and temperature.
Procedure to set and store up to 40 charge/discharge profiles.
How to recall previously saved battery program memories.
Configure safety timer and maximum charge capacity limits.
Set temperature limits for charging and choose display unit (C/F).
Allows setting a cool-down period between charge/discharge cycles.
Adjust NiMH sensitivity and configure key beep/buzzer.
Configure DC input voltage cut-off and balance connection.
Set AC max power per channel and load factory defaults.
Operate, monitor, and control the charger using PC software.
Step-by-step guide to update the Q200 firmware via USB.
Utilize smartphone app via Bluetooth for remote control and monitoring.
Guide to selecting battery type, methods, current, and system settings in the app.
Procedure for adding new charging programs using the mobile app.
States limitations of liability for charger use and misuse.
Covers warranty period, scope, and overseas service information.
To Next Page
