Skyrc e4 - User Manual

Thank you for your choice of the SKYRC e4, 100-240V AC balance charger. This unit is simple to use but
its operation does require some knowledge on the part of the user. Please read this entire operating
manual completely and attentively before using this product, as it covers a wide range of information on
operating and safety.
SKYRC e4 Charger is an economic, high quality 100-240V AC balance charger, designed for charging
LiPo and LiFe batteries from 2-4 cells in balance mode. The circuit power is 20W and max charge current
can reach to 3A. There are three kinds of charge current 1A/2A/3A that can be selected. You could select
the proper charge current according to battery capacity.
INSTRUCTION MANUAL
INTRODUCTION
CHARGE PROCEDURES
SKYRC e4 comes with the built in power supply. You can connect the AC power cord to the AC socket
(100-240V AC) directly.
Insert the AC power cord into the charger.
Insert the AC cord into a wall socket (100-240V). All LEDS will light for 1 second and the charge
status LED will flash green which indicates the charger is ready to charge.
Select the battery type LiPo/LiFe by the toggle switch.
Select the proper charging current 1A/2A/3A by the toggle switch.
Connect the battery main charge lead to battery socket which is in the front side of the charger and
battery balance wire to balance port which is in the right side of the charger.
The charger starts charging. The charge status LED and the cell status LED will glow constant red. If
the battery pack is 2-cell, Cell 1 and Cell 2 LEDs will glow constant red; if the battery pack is 3-cell,
Cell 1, Cell 2 and Cell 3 LEDs will glow constant red; and so on.
During the charging progress, when the charge
status LED glows constant red, the charger is
charging in CC mode; when the charge status
LED glows constant orange, the charger is
charging in CV mode;
When the cell LED is flashing, this cell is
discharging for balancing.
When the battery is fully charged, the charge
status LED will glow constant green.
Unplug the battery from the charger and the
charge status LED will flash green which
indicates the charger is ready to charge
another battery.
Please refer to following steps to charge the battery,
1)
2)
3)
4)
5)
6)
7)
8)
9)
- 1 - - 2 -
SPECIFICATION
AC Input
Battery Type
Cell Count
Charge Current
Circuit Power
Current Drain for Balancing
Dimension
Weight
Charger/Cell Status
100-240V
LiPo/LiFe
2-4 cells
1A/2A/3A ± 10%
20W
200mA
69.4x110.7x40.5mm
176g
SK-100055
This diagram shows the correct way to connect your
battery to the e4 charger while charging in balance
mode.
Failure to connect as shown in this diagram will
damage this charger.
CAUTION:
CONNECTION DIAGRAM
Charger
Battery
10)
Battery Type Switch
Cell 2 LED Indicator
Cell 1 LED Indicator
Cell 4 LED Indicator
Cell 3 LED Indicator
Battery Socket
AC 100-240V
Power Jack
Charge Current Switch
Charge Status LED Indicator
Balance Socket
EXPLANATION OF LED STATUS
If the charger encounters a problem, all LEDs will flash red in sequence to alert you the errors. In this
case, please disconnect the power cord from the wall socket and unplug the battery from the charger.
* Error Message
LED green blinking
LED glows constant red
LED glows constant orange
LED glows constant green.
LED glows constant red.
LED flashes red
The charger is ready to charge.
The charger is charging in CC mode.
The charger is charging in CV mode.
The charging process finishes.
The cell is charging.
The cell is discharging.
Charge Status LED
Cell Status LED

Summary

Introduction and Basic Operation

Charge Procedures

Step-by-step guide on connecting and initiating charging for LiPo/LiFe batteries.

LED Status Explanation

Details the meaning of various LED indicators during charging and error states.

Charger Specifications

Technical details including input, battery type, cell count, current, power, and dimensions.

Product Details and Compliance

Package Contents

Lists all items included in the SKYRC e4 charger package.

Recommended Accessories

Suggests compatible charging cables for different battery connectors.

Safety Warnings

Crucial safety notes for proper and safe operation of the battery charger.

Conformity Declaration

States compliance with CE and FCC standards and lists tested technical standards.

Warranty and Service Information

Details the product warranty period, terms, and service procedures.

Liability Exclusion

Defines SKYRC's limitations of liability for product misuse or incorrect operation.

Skyrc e4 Specifications

General

Input voltage	100-240 V
Input frequency	50/60 Hz
Type	Indoor battery charger
Number of batteries supported	4
Compatible battery technologies	Lithium Polymer (LiPo)
Quantity per pack	1 pc(s)
Product color	Black
Built-in display	No
Output	20W

Weight and Dimensions

Depth	110.7 mm
Width	69.4 mm
Height	40.5 mm
Weight	176 g