Need help?Do you have a question about the SMART Board Board 800ix2 and is the answer not in the manual?
General safety warnings, cautions, and important operational information.
Guidance and warnings related to the installation process of the system.
Details the WXGA (16:10) ultra-short-throw, high-offset SMART UX80 projector features.
Describes the SMART Board 800 series interactive whiteboard and its DVI technology.
Lists features of the SMART UX80 projector, including DLP technology and connectivity.
Lists and describes accessories like remote control, pens, eraser, GoWire cable.
Guidance on selecting an optimal location for the interactive whiteboard system.
Instructions on mounting the projector at the correct height for optimal image alignment.
Instructions on properly routing cables between the projector and whiteboard.
Steps for installing essential SMART software for system functionality.
Steps for focusing and aligning the projected image for optimal display.
Illustrates projector connections for various peripheral devices.
Explains how to use the projector's remote control for settings and menus.
Details the functions of the projector's remote control buttons.
Explains how to use the ECP for basic system operations and controls.
Instructions on connecting and using the SMART GoWire cable for software access.
Precautions to prevent damage to the interactive whiteboard surface.
Tips for cleaning the interactive whiteboard's writing surface effectively.
Instructions for cleaning the pen tray and its infrared sensors.
Guidelines and warnings for safely cleaning the projector lens and components.
Instructions on how to replace the projector lamp module when needed.
Procedure for resetting projector lamp hours after replacement.
Steps for replacing the battery in the projector remote control.
Initial steps before troubleshooting, like locating status lights and serial numbers.
Identifies the location of status lights on the system components.
Describes where to find serial numbers for the whiteboard, projector, and ECP.
Table to help diagnose system status using indicator lights.
General guidance for resolving issues with the interactive whiteboard.
Steps to resolve basic operational problems with the whiteboard.
Troubleshooting steps for connection problems between system components.
Addresses common projector errors like overheating or lamp failure.
Solutions for common problems with the projected image.
Steps to troubleshoot problems with audio output.
Guidance for troubleshooting network connectivity problems.
Troubleshooting steps if the ECP is not receiving power.
Instructions for system administrators to access the service menu.
How to retrieve a forgotten projector password.
Procedure to reset all projector settings to factory defaults.
Accessing advanced setup features via the projector's web page.
Managing projector audio, video status, alerts, and appearance via browser.
Managing the projector's USB settings.
Viewing projector service details like lamp hours and temperature.
Configuring DHCP, IP address, subnet mask, and other network parameters.
Setting up e-mail alerts for projector events.
Enabling administrator password for web management.
Information on SNMP commands and MIB file usage.
Using Crestron RoomView for projector control via IT network.
Connecting a computer or control system to the projector via RS-232.
Configuring serial data communication settings for projector control.
Overview of projector programming commands for various functions.
Commands to control projector power states and request status.
Commands to control the projector's video display output.
Commands to control the projector's audio output.
Commands for controlling projector integration properties.
Commands for retrieving projector model, serial, and firmware versions.
Commands to control network integration properties.
Lists the projector's native and compatible VESA RGB and HDMI video formats.
Details projector compatibility with high and standard definition signal formats.
Lists projector compatibility for HDMI video signals by video mode.
Instructions for connecting peripheral devices like laptops and players.
Lists the vendor and key codes for each button on the remote control.
Explains regulations for disposal of electronic equipment and batteries.
Information on the CR2025 battery in the remote and proper disposal.
Notes the presence of perchlorate material and special handling.
States that the lamp contains mercury and requires proper disposal.
General safety warnings, cautions, and important operational information.
Guidance and warnings related to the installation process of the system.
Details the WXGA (16:10) ultra-short-throw, high-offset SMART UX80 projector features.
Describes the SMART Board 800 series interactive whiteboard and its DVI technology.
Lists features of the SMART UX80 projector, including DLP technology and connectivity.
Lists and describes accessories like remote control, pens, eraser, GoWire cable.
Guidance on selecting an optimal location for the interactive whiteboard system.
Instructions on mounting the projector at the correct height for optimal image alignment.
Instructions on properly routing cables between the projector and whiteboard.
Steps for installing essential SMART software for system functionality.
Steps for focusing and aligning the projected image for optimal display.
Illustrates projector connections for various peripheral devices.
Explains how to use the projector's remote control for settings and menus.
Details the functions of the projector's remote control buttons.
Explains how to use the ECP for basic system operations and controls.
Instructions on connecting and using the SMART GoWire cable for software access.
Precautions to prevent damage to the interactive whiteboard surface.
Tips for cleaning the interactive whiteboard's writing surface effectively.
Instructions for cleaning the pen tray and its infrared sensors.
Guidelines and warnings for safely cleaning the projector lens and components.
Instructions on how to replace the projector lamp module when needed.
Procedure for resetting projector lamp hours after replacement.
Steps for replacing the battery in the projector remote control.
Initial steps before troubleshooting, like locating status lights and serial numbers.
Identifies the location of status lights on the system components.
Describes where to find serial numbers for the whiteboard, projector, and ECP.
Table to help diagnose system status using indicator lights.
General guidance for resolving issues with the interactive whiteboard.
Steps to resolve basic operational problems with the whiteboard.
Troubleshooting steps for connection problems between system components.
Addresses common projector errors like overheating or lamp failure.
Solutions for common problems with the projected image.
Steps to troubleshoot problems with audio output.
Guidance for troubleshooting network connectivity problems.
Troubleshooting steps if the ECP is not receiving power.
Instructions for system administrators to access the service menu.
How to retrieve a forgotten projector password.
Procedure to reset all projector settings to factory defaults.
Accessing advanced setup features via the projector's web page.
Managing projector audio, video status, alerts, and appearance via browser.
Managing the projector's USB settings.
Viewing projector service details like lamp hours and temperature.
Configuring DHCP, IP address, subnet mask, and other network parameters.
Setting up e-mail alerts for projector events.
Enabling administrator password for web management.
Information on SNMP commands and MIB file usage.
Using Crestron RoomView for projector control via IT network.
Connecting a computer or control system to the projector via RS-232.
Configuring serial data communication settings for projector control.
Overview of projector programming commands for various functions.
Commands to control projector power states and request status.
Commands to control the projector's video display output.
Commands to control the projector's audio output.
Commands for controlling projector integration properties.
Commands for retrieving projector model, serial, and firmware versions.
Commands to control network integration properties.
Lists the projector's native and compatible VESA RGB and HDMI video formats.
Details projector compatibility with high and standard definition signal formats.
Lists projector compatibility for HDMI video signals by video mode.
Instructions for connecting peripheral devices like laptops and players.
Lists the vendor and key codes for each button on the remote control.
Explains regulations for disposal of electronic equipment and batteries.
Information on the CR2025 battery in the remote and proper disposal.
Notes the presence of perchlorate material and special handling.
States that the lamp contains mercury and requires proper disposal.
General| Brand | SMART Board |
|---|---|
| Model | Board 800ix2 |
| Category | Interactive whiteboard |
| Language | English |
To Next Page
