Smeg LBP3T84PIT - User Manual

Questions and Answers

C
crystal45Aug 13, 2025
How to fix a Smeg Washer that won't start?
- M
  Maria Medina MDAug 13, 2025
  If your Smeg Washer doesn't start, several factors could be at play. First, ensure the machine is properly plugged into a functioning power outlet. Check the fuses and replace them if they are faulty. Verify that there is mains power supply. Make sure you have pressed the Start/Pause button. Also, ensure the program dial is not in the ‘stop’ position; if it is, turn it to the desired setting. Finally, confirm that the machine door is completely closed.
J
Justin ShahAug 16, 2025
What to do if my Smeg LBP3T84PIT Washer does not discharge water?
- H
  herrerarobertAug 16, 2025
  If your Smeg Washer isn't discharging water, inspect the drain hose for clogs or twists; clean or untwist it as needed. Also, the pump filter might be clogged, so clean it. Ensure that your laundry is spread evenly in the machine.
T
Teresa DanielsAug 20, 2025
Why is the spin cycle delayed on my Smeg Washer?
- T
  Thomas WillisAug 20, 2025
  If the spin cycle on your Smeg Washer doesn't start or starts later than expected, it's likely that the Unbalanced load control system has been activated. This system will attempt to spread your laundry. The spinning cycle will begin once your laundry is spread. For the next wash, load the drum evenly.
Q
qirwinAug 25, 2025
Why is my Smeg Washer not intaking water?
- H
  Haley BuckAug 25, 2025
  If your Smeg Washer isn't taking in water, start by checking if the water tap is turned on. Next, inspect the water inlet hose for any twists and untwist it if necessary. Also, the water inlet hose or the inlet filter may be clogged, so clean these filters. Finally, ensure that the machine door is completely closed.
F
fergusonbeckyAug 28, 2025
How to stop my Smeg LBP3T84PIT from vibrating?
- M
  Mrs. Crystal HernandezAug 28, 2025
  If your Smeg Washer is vibrating, make sure the feet have been properly adjusted. Another potential cause is the transit bolts, which are fitted for transportation; these need to be removed. Avoid setting up your washing machine on a hard surface. Also, ensure that the machine is not overloaded and that the laundry is spread evenly in the drum.
W
Wayne GarciaSep 1, 2025
Why is there so much foam in my Smeg Washer detergent drawer?
- J
  jonathan60Sep 1, 2025
  If you notice excessive foam in the detergent drawer of your Smeg Washer, it could be due to using too much detergent or using the wrong type. To stop the foam, press the Start/Pause button, then dilute one tablespoon of softener into 1/2 litre of water and pour it into the detergent drawer. Press the Start/Pause button again after 5-10 minutes. Ensure you only use detergents specifically produced for automatic washing machines.
X
xabbottSep 4, 2025
Why does my Smeg LBP3T84PIT Washer discharge water as soon as it is loaded?
- J
  Jonathan RollinsSep 4, 2025
  If your Smeg Washer is loaded with water and the water discharges immediately, it means that the end of the water drain hose is too low for the machine. Check that the drain hose is at a suitable height.
D
David WardSep 8, 2025
Why is my Smeg Washer not washing clothes properly?
- A
  Angel HarrisonSep 8, 2025
  If you're not getting satisfactory washing results from your Smeg Washer, consider whether your laundry is too dirty for the selected program; if so, select a more appropriate program. Also, ensure you're using enough detergent as instructed on the packaging. Finally, check that you have not exceeded the maximum laundry capacity for the selected program.