EasyManua.ls Logo

Smeg LBW50CIT - User Manual

Smeg LBW50CIT
32 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
LBW50CIT
Washing Machine / User Manual
EN

Table of Contents

Questions and Answers

  • J
    Joshua ConnerAug 16, 2025
    Why my Smeg Washer doesn't start?
    • A
      Andrea AdamsAug 16, 2025
      Your Smeg Washer might not start due to several reasons: it may not be plugged in, the fuses could be faulty, there might be no mains power supply, the Start/Pause button hasn't been pressed, the programme dial is in the ‘stop’ position, or the machine door isn't completely closed. Try plugging the machine in, replacing the fuses, checking the mains power, pressing the Start/Pause button, turning the programme dial to the desired position, and ensuring the door is completely closed.
  • R
    Rebecca DiazAug 19, 2025
    Why Smeg LBW50CIT spin cycle is delayed?
    • M
      melissawardAug 19, 2025
      If the spin cycle in your Smeg Washer doesn't take place or is delayed, it could be because the Unbalanced load control system has been activated. The system will try to spread your laundry, and the spinning cycle will begin once it's spread. Load the drum evenly for the next wash.
  • M
    Mr. Eric PatelAug 22, 2025
    How to fix Smeg Washer not discharging water?
    • A
      Annette JonesAug 22, 2025
      If your Smeg Washer isn't discharging water, the drain hose might be clogged or twisted, or the pump filter could be clogged. Also, laundry may be too tightly packed in the drum. Check, clean, or untwist the drain hose, clean the pump filter, and spread your laundry evenly in the machine.
  • S
    Stephanie BallardAug 25, 2025
    Why Smeg LBW50CIT washing result is unsatisfactory?
    • K
      Kelly RobertsAug 26, 2025
      An unsatisfactory washing result from your Smeg Washer could be because the washing is too dirty for the selected programme, not enough detergent was used, or there is too much laundry in the machine. Select the most appropriate programme using the programme tables, use the amount of detergent as instructed on the packaging, and check that the maximum capacity for the selected programme has not been exceeded.
  • D
    Deborah HullAug 27, 2025
    What to do if Smeg Washer doesn't intake water?
    • B
      browncharlesAug 27, 2025
      If your Smeg Washer isn't taking in water, the water tap might be turned off, the water inlet hose could be twisted or clogged, or the inlet filter might be clogged. Also, the machine door may not be completely closed. Ensure the tap is on, check and untwist the water inlet hose, clean the water inlet hose filters and inlet filters, and close the machine door completely.
  • L
    Laura AvilaAug 30, 2025
    Why does Smeg LBW50CIT Washer vibrate so much?
    • W
      William MorrisonAug 30, 2025
      Excessive vibration in your Smeg Washer can occur if the feet haven't been adjusted, transit bolts used for transportation haven't been removed, the machine is overloaded or the laundry is unevenly spread, or the machine is placed on a hard surface. Adjust the feet, remove the transit bolts, avoid overloading and spread laundry evenly, and do not place the washer on a hard surface.
  • S
    Steven KellerSep 2, 2025
    What to do if Smeg LBW50CIT Washer has excessive foam?
    • D
      David HernandezSep 2, 2025
      Excessive foam in the detergent drawer of your Smeg Washer can be due to using too much detergent or using the wrong type of detergent. To stop the foam, press the Start/Pause button, dilute one tablespoon of softener into 1/2 litre of water, pour into the detergent drawer, and press the Start/Pause button after 5-10 minutes. Only use detergents specifically produced for automatic Washing Machines.
  • J
    Jaime BartlettSep 4, 2025
    Why Smeg LBW50CIT Washer discharges water as soon as it is loaded?
    • T
      Todd BrownSep 5, 2025
      If your Smeg Washer discharges water as soon as it's loaded, the end of the water drain hose might be too low. Check that the drain hose is at a suitable height.
  • R
    Robert LaneSep 7, 2025
    Why my laundry has detergent residue after washing in Smeg LBW50CIT Washer?
    • J
      Joshua StanleySep 7, 2025
      If your laundry has detergent residue after washing in your Smeg Washer, non-dissolving particles of some detergents may be appearing as white spots. Perform an extra rinse, or clean your laundry with a brush after it dries.
  • W
    William ParsonsSep 10, 2025
    Why do grey spots appear on laundry after washing in Smeg LBW50CIT Washer?
    • J
      Jeanette BirdSep 10, 2025
      If grey spots appear on your laundry after washing in your Smeg Washer, there might be untreated oil, cream, or ointment on the laundry. Use the amount of detergent as instructed on the packaging in the next wash.

Smeg LBW50CIT Specifications

General IconGeneral
BrandSmeg
ModelLBW50CIT
CategoryWasher
LanguageEnglish

Related product manuals