EasyManua.ls Logo

Smeg LBW912IT - User Manual

Smeg LBW912IT
32 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Washing Machine / User Manual
EN
LBW912IT

Table of Contents

Questions and Answers

  • V
    Vanessa BurtonAug 17, 2025
    How to fix a Smeg LBW912IT that won't start?
    • D
      Dana NguyenAug 17, 2025
      If your Smeg Washer doesn't start, there might be several reasons: * It might not be plugged in, so ensure it is properly connected to a power outlet. * The fuses could be faulty, requiring replacement. * There might be no mains power supply, so check your power source. * The Start/Pause button may not have been pressed; make sure to press it. * The programme dial might be in the ‘stop’ position; turn it to the desired programme. * The machine door might not be completely closed; ensure it is securely shut.
  • J
    Jason MillsAug 20, 2025
    What to do if my Smeg LBW912IT is not intaking water?
    • J
      Jessica PetersonAug 20, 2025
      If your Smeg Washer isn't intaking water, check the following: * Ensure the water tap is turned on. * Inspect the water inlet hose for any twists and untwist it. * The water inlet hose might be clogged, so clean the filters. * The inlet filter itself could be clogged, so clean the inlet filters. * Also, make sure that the machine door is completely closed.
  • A
    alicialoganAug 23, 2025
    Why is my Smeg LBW912IT Washer vibrating so much?
    • R
      Raymond Blackburn MDAug 23, 2025
      If your Smeg Washer vibrates, it could be due to a few reasons: * The feet may not be adjusted properly; make sure to adjust them. * Transit bolts fitted for transportation might not have been removed; remove them. * If you have a small load in the drum, this won't prevent operation of your machine. * The machine might be overloaded or the laundry is unevenly spread; avoid overloading and spread laundry evenly. * The machine could be resting on a hard surface; avoid setting up your washer on a hard surface.
  • L
    larry55Aug 26, 2025
    What to do if my Smeg LBW912IT does not discharge water?
    • J
      Jeffrey RiggsAug 26, 2025
      If your Smeg Washer isn't discharging water, check the following: * The drain hose might be clogged or twisted; inspect, clean, or untwist it. * The pump filter could be clogged; clean the pump filter. * Your laundry might be too tightly packed; spread your laundry evenly in the machine.
  • M
    Michael WoodardAug 28, 2025
    Why does my Smeg LBW912IT Washer discharge water immediately after loading?
    • R
      Ryan WeaverAug 28, 2025
      If water discharges as soon as your Smeg Washer is loaded, it's likely because the end of the drain hose is too low. Check that the drain hose is at a suitable height.
  • J
    Jessica MartinAug 31, 2025
    Why is my Smeg Washer not cleaning clothes properly?
    • S
      sean16Aug 31, 2025
      If your Smeg Washer isn't washing properly, consider these points: * Your laundry might be too dirty for the selected program; use the program tables to select the most appropriate program. * You might not be using enough detergent; use the amount instructed on the packaging. * There might be too much laundry in your machine; check that you haven't exceeded the maximum capacity for the selected program.
  • S
    Sarah BurkeSep 3, 2025
    Why are there grey spots on my laundry after washing in my Smeg Washer?
    • M
      murrayfrankSep 3, 2025
      If you see grey spots on your laundry after washing with your Smeg Washer, it could be due to untreated oil, cream, or ointment on your laundry. Use the amount of detergent as instructed on the packaging in the next wash.
  • M
    Marcus RobinsonSep 5, 2025
    Why is the spin cycle delayed in my Smeg LBW912IT?
    • D
      Danielle JonesSep 5, 2025
      If the spin cycle in your Smeg Washer is delayed or doesn't occur, it may be because the Unbalanced load control system has been activated. This system will attempt to spread your laundry, and the spinning cycle will begin once the laundry is spread. For the next wash, load the drum evenly.
  • G
    gregory18Sep 8, 2025
    How to reduce excessive foam in my Smeg LBW912IT detergent drawer?
    • X
      xhallSep 8, 2025
      If you observe excessive foam in the detergent drawer of your Smeg Washer: * You might be using too much detergent. Press the Start/Pause button, then dilute one tablespoon of softener in 1/2 litre of water and pour it into the drawer. Press Start/Pause again after 5-10 minutes. * You might be using the wrong detergent. Ensure you only use detergents specifically produced for automatic Washing Machines.
  • C
    christopherhodgeSep 12, 2025
    How to remove detergent residue from laundry after washing in Smeg LBW912IT Washer?
    • D
      danielstracySep 12, 2025
      If your laundry has detergent residue after using your Smeg Washer, it's because non-dissolving particles of some detergents may appear as white spots. Perform an extra rinse or clean your laundry with a brush after it dries.

Smeg LBW912IT Specifications

General IconGeneral
TypeFront Load
Capacity9 kg
Spin Speed1200 rpm
Energy RatingA+++
Weight70 kg
ColorWhite
Programs15
Delay StartYes
Child LockYes

Related product manuals