Why my Smeg SWM107E Washer doesn't start?
Your Smeg Washer might not start due to several reasons: * It is not plugged in, so plug it in. * The fuses are out of order, so replace them. * There's an electricity cut-off, so check the mains power. * The start/pause button wasn't pressed, so press it. * The programme knob is on position 0, so switch it to the desired position. * The machine door isn't completely closed, so close it.
What to do if my Smeg Washer vibrates?
If your Smeg Washer is vibrating, consider the following: * The stays of your machine may not be adjusted. Adjust them. * The safety assembly fitted for transport may not be disassembled. Disassemble it. * There might be less amount of laundries in the appliance, but this will not block operation of your machine. * Your machine might be overloaded with laundries or laundries settled non-homogeneously. Do not put laundries more than the amount recommended and settle the laundries in the machine homogeneously. * Your machine might be resting on a hard surface. Prevent your machine from resting on hard surfaces by leaving 2 cm space between it and wall or hard surfaces.
Why my Smeg Washer does not intake water?
If your Smeg Washer isn't taking in water, it could be due to a few reasons: * Your faucet might be turned off, so turn it on. * The water inlet hose may be twisted, so check it. * The water inlet hose might be clogged, so clean the water inlet hose filters. * The valve inlet filter could be clogged, so clean the valve inlet filters. * The machine door isn't completely closed, so close it.
What to do if Smeg SWM107E does not discharge water?
If your Smeg Washer isn't discharging water, check these: * The discharging hose could be clogged or twisted. Check the discharging hose. * The pump filter might be clogged. Clean the pump filter. * Laundries settled in the machine non-homogeneously. Spread your laundries in the machine properly and homogeneously.
Why is excessive foam formed in the detergent drawer of my Smeg SWM107E Washer?
Excessive foam in the detergent drawer of your Smeg Washer is likely due to: * Using an excessive amount of detergent. Press on Start/Pause button. To eliminate foam formation, mix a spoon of softener with half litres of water and pour the mixture in the detergent drawer. After 5-10 minutes, press on Start/Pause button again. In next washing operation, decide the dose of detergent as required. * Using the wrong detergent. Use detergents produced only for automatic washing machines in your machine.
Why my Smeg SWM107E gives unsatisfactory washing result?
An unsatisfactory washing result from your Smeg Washer may occur because: * The contamination degree of your laundries does not match the programme you have chosen. Select the programme appropriate for the contamination degree of your laundries. * The amount of detergent used is insufficient. Adjust the amount of detergent based on the amount and contamination degree of your laundries. * You've put laundries in excess of maximum capacity in your machine. Load your machine with laundries, amount of which will not exceed maximum laundry capacity.
Why does my Smeg SWM107E Washer give unsatisfactory washing result?
If you're seeing unsatisfactory washing results with your Smeg Washer, it could be due to: * Water being hard (dirty, hard, etc.). Adjust the amount of detergent based on the instruction of detergent manufacturer. * Laundries distributed in your machine non-homogenously. Spread your laundries in the machine properly and homogeneously.
What to do if laundries have detergent residues on them after washing in my Smeg Washer?
If your laundries have detergent residues after washing in your Smeg Washer, it's because non-dissolving particles of some detergents may adhere to your laundries as white spots. Perform an extra rinsing by setting your machine to “Rinsing” programme, or clean the spots using a brush after your laundries dries.
Why does my Smeg SWM107E discharge water as soon as it is loaded with water?
If your Smeg Washer discharges water as soon as it's loaded, it's likely because the end of water discharging hose is too low for the machine. Set the water discharging hose on appropriate height.
Why grey spots appear on the laundries after washing in my Smeg Washer?
If grey spots appear on the laundries after washing in your Smeg Washer, the reason for this spots may be oil, cream or ointment. Apply the maximum amount of detergent instructed by the detergent manufacturer in the next washing operation.
To Next Page
General
