Snapper LT150H331BV, LT150H38IBV, WLT150H38IBV, WLT170H38IBV, User Manual

Snapper LT150H331BV, LT150H38IBV, WLT150H38IBV, WLT170H38IBV,

44 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

Safety Instructions & Operator’s Manual for

LAWN TRACTOR

HYDROSTATIC DRIVE

SERIES I

MODELS

LT150H33IBV

LT150H38IBV

WLT150H38IBV

WLT170H38IBV

MODEL NUMBER EXPLANATION

LT 150 H 38 I B V

MODEL DESIGNATION

ENGINE HP ENGINE TYPE

DRIVE SYSTEM TYPE ENGINE MODEL

CUTTING WIDTH SERIES DESIGNATION

LT – Lawn Tractor Model Designation 33 – 33” Cutting Width Mower

WLT – Lawn Tractor Model Designation 38 – 38” Cutting Width Mower

150 – 15.0 HP Engine Horse Power I – Series Designation

170 – 17.0 HP Engine Horse Power B – Briggs & Stratton

H – Hydrostatic Transmission V – Over Head Valve Type Engine

Thank you for buying a SNAPPER product! Before operating the Lawn Tractor, read and follow the

“IMPORTANT SAFETY INSTRUCTIONS” on pages 2 & 3, all other instructions contained in this manual and the

accompanying booklet “About Power Mower Safety”. Lawn mowers and all power equipment can be potentially

dangerous if used improperly. REMEMBER: SAFETY REQUIRES CAREFULL USE IN ACCORDANCE WITH

INSTRUCTIONS AND COMMON SENSE!

COPYRIGHT © 2002

SNAPPER INC.

ALL RIGHTS RESERVED

MANUAL No. 7-2343 (I.R. 6/28/02)

Table of Contents

Questions and Answers:

W
William CastroJul 30, 2025
Why Snapper LT150H331BV, LT150H38IBV, WLT150H38IBV, WLT170H38IBV, engine will not start?
- M
  Matthew FosterJul 30, 2025
  Several factors can prevent your Snapper lawn mower engine from starting. Ensure the blade engagement switch is in the “OFF” position and the park brake is set. Check that the fuel tank isn't empty and fill it with fresh fuel if needed. If the engine needs choking, move the engine speed control to “CHOKE”. Also, make sure the spark plug wire is securely connected to the spark plug. A weak or dead battery can also be the culprit, so service the battery. If none of these resolve the issue, there may be a faulty interlock switch and you should contact an authorized SNAPPER dealer.
L
Lindsay StevensAug 3, 2025
What to do if Snapper LT150H331BV, LT150H38IBV, WLT150H38IBV, WLT170H38IBV, Lawn Mower starter will not crank engine?
- A
  Angela WestAug 3, 2025
  If the starter on your Snapper lawn mower won't crank the engine, begin by servicing the battery. Check and replace the fuse if it's blown. Ensure all electrical connections are clean and making good contact. If the issue persists, the ignition switch may be defective, requiring you to contact an authorized SNAPPER dealer. If the starter spins without engaging, release the start key and try again; if it continues to spin, contact an Engine Dealer.
W
Wendy WongAug 8, 2025
Why does Snapper LT150H331BV, LT150H38IBV, WLT150H38IBV, WLT170H38IBV, Lawn Mower engine stall after running?
- J
  Joseph DavisAug 8, 2025
  Your Snapper lawn mower engine might stall after running due to several reasons. Make sure you are sitting in the operator's seat. Ensure the engine speed control is not in the “CHOKE” position, but rather in the “FAST” position. Check the fuel level and refill if necessary. Clean the engine air pre-cleaner and/or air cleaner if they are dirty. Service the spark plug if it’s defective or the gap is improperly set. Replace the fuel filter if it's clogged. Lastly, drain and clean the fuel system to remove any water, debris, or stale fuel.
J
jessicadunnAug 14, 2025
How to fix Snapper LT150H331BV, LT150H38IBV, WLT150H38IBV, WLT170H38IBV, Lawn Mower engine loses power?
- A
  ambergonzalezAug 14, 2025
  If your Snapper lawn mower engine is losing power, try the following: reduce the load on the engine by slowing down. Clean or replace the engine air pre-cleaner or air cleaner if they are dirty. Ensure the engine oil level is at the correct level. Clean any debris from the engine cooling fins and air screens. Service the spark plug. Finally, drain and clean the fuel system to eliminate any water, debris, or stale fuel.
S
stevensjoannaAug 18, 2025
Why does Snapper LT150H331BV, LT150H38IBV, WLT150H38IBV, WLT170H38IBV, engine backfire when turned to “STOP”?
- J
  jgomezAug 18, 2025
  If your Snapper lawn mower engine backfires when turned to “STOP”, it might be because the engine speed control is set too “FAST”. Set the engine speed control to “SLOW” and allow the engine to idle before turning the key to “OFF.”

Snapper LT150H331BV, LT150H38IBV, WLT150H38IBV, WLT170H38IBV, Specifications

General

Engine	Briggs & Stratton
Transmission	Hydrostatic
Drive System	Rear-wheel drive
Number of Blades	2
Blade Engagement	Manual
Engine Type	4-Cycle
Turning Radius	18 inches
Warranty	2 years limited

Summary

Snapper Lawn Tractor Model Identification

Model Number Explanation

Explains the designation of model numbers for Snapper lawn tractors.

Important Safety Instructions

Protection for Children

Guidelines for ensuring children's safety during mower operation.

Protection Against Tip-overs

Safety measures to prevent machine tip-overs on slopes and uneven terrain.

Preparation for Operation

Essential steps before starting the tractor, including reading the manual and checking the area.

Section 1 - Familiarization

Components Overview

Identifies and illustrates the main components of the Snapper Lawn Tractor.

Control Panel Layout

Details the location and function of controls on the tractor's dashboard.

Section 2 - Operating Instructions

Pre-Start Checklist

Mandatory checks and services to perform before each engine start-up.

Operator's Seat Adjustment

Instructions for adjusting the operator's seat for comfort and safe operation.

Starting Engine Procedures

Step-by-step guide for starting the lawn tractor engine.

Driving and Blade Operation

Procedures for starting wheel drive, mower blades, and stopping systems.

Cutting Height and Park Brake

Adjusting cutting height and using the park brake system.

Tractor Movement and Reverse Lockout

Procedures for moving the tractor with engine off and using the reverse lockout feature.

Section 3 - Maintenance

Initial Service (First 5 Hours)

Initial maintenance tasks required after the first 5 hours of operation.

Maintenance Tasks (25 Hours)

Maintenance tasks to be performed every 25 operating hours.

Tractor Lubrication Points

Details on lubricating various tractor components like bearings and spindles.

Annual Service Items

Procedures for fuel filter, spark plug, and hydrostatic transmission oil.

Section 4 - Adjustment & Repair

Engine, Deck, and Blade Adjustments

Adjustments for engine, mower deck components, and blades.

Deck Leveling Procedures

Instructions for leveling the mower deck side-to-side and front-to-rear.

Drive Component Adjustments

Adjusting brakes, steering, shifter, and traction drive belts.

Blade Service and Replacement

Procedures for checking blade wear, sharpening, and replacing blades.

Section 5 - Electrical System

Wiring Harness Schematic

Diagram of the electrical wiring harness for B&S engines.

Troubleshooting Guide

Engine and Starting Problems

Common issues related to engine starting, stalling, and power loss.

Operation and Component Issues

Troubleshooting problems with tractor movement, blade operation, and grass cutting.

Cutting and Charging Issues

Addressing issues with grass cutting and battery charging.

Maintenance Schedule and Parts

Scheduled Maintenance Tasks

Table outlining maintenance tasks by service intervals.

Maintenance Parts Information

List of drive belts and mower blades by tractor model.

Primary Maintenance Focus

Importance of Primary Maintenance

Overview of why primary maintenance is crucial for engine longevity.

Air Cleaner Service Importance

Details the negative consequences of an improperly serviced air cleaner.

Engine Cooling and Fuel Contamination

Instructions for cleaning engine cooling fins and fuel storage guidance.

Engine Lubrication and Starting Checklist

Emphasizes checking engine oil and provides a starting checklist.

Snapper Product Registration

Product Registration Process

Instructions and contact details for registering the Snapper product for warranty.

Important Product Information and Warnings

Emissions and Safety Warnings

Information regarding emissions compliance and critical safety warnings.

Related product manuals

Preview: Snapper LT12

Preview: Snapper LT12D41

Snapper LT12D41

Snapper LT14H331KV

Snapper LT140H331KV

Snapper LT160H42FBV

Snapper LT145H38FBV

Snapper LT145H38GBV

Snapper LT145H38DBV

Snapper LT145H33FBV, LT145H38FBV

Preview: LT160H42GBV, 2LT160H42GBV2, LT180H48GBV2

LT160H42GBV, 2LT160H42GBV2, LT180H48GBV2

Preview: LT180H42IBV, LT200H42IBV2, LT200H48IBV2

LT180H42IBV, LT200H42IBV2, LT200H48IBV2

Preview: ELT18538, ELT2044, LT18538, LT18500, LT2042, LT2044, LT22500

ELT18538, ELT2044, LT18538, LT18500, LT2042, LT2044, LT22500