Snapper Z-rider - User Manual

1
SET-UP INSTRUCTIONS & PRE-OPERATION CHECKLIST
SNAPPER ZERO TURNING Z-RIDER with MID MOUNT MOWER
INTRODUCTION: These instructions cover the set-up of the Snapper Mid Mount Z-Rider Mower. Complete each
of the following steps carefully. Review and complete each item as instructed on the Pre-Operation checklist.
The Snapper Product Registration card must be filled out and sent to Customer Service department at Snapper
when completed.
IMPORTANT: The battery for this unit is shipped dry. A package of battery acid (electrolyte) will have to be
purchased separately. Allow sufficient time for charging and installing the battery before operating the rider.
Pay close attention to the precautionary statements on the battery and in these instructions. You will also need
an automotive type battery charger to activate the battery for use.
STEP 1: Remove machine from the container. The
battery will have to be charged and installed.
STEP 2: Remove battery from the battery compartment
before charging.
STEP 3: Place battery in a well ventilated area on a
level non-concrete surface.
WARNING
The electrolyte (acid) produces a highly explosive gas.
Keep all sparks, flame and fire away from area when
charging battery or when handling electrolyte or
battery. Electrolyte (acid) is a highly corrosive liquid.
Wear eye protection. Wash affected areas immediately
after having eye or skin contact with electrolyte (acid).
Battery acid is corrosive. Rinse empty acid containers
with water and mutilate before discarding. If acid is
spilled on battery, bench, or clothing, etc., Flush with
clear water and neutralize with baking soda.
STEP 4: Remove battery cell caps. Fill cells as required
with electrolyte (purchased separately) to proper level.
Filling battery with electrolyte will bring the battery to
80% charged state.
WARNING
DO NOT OVERFILL!
STEP 5: With cell caps removed, connect battery
charger to battery terminals; RED to positive (+) and
BLACK to negative (-) terminal.
STEP 6: Slow charge the battery at 2 amp for 2 hours
to bring the battery to full charge.
STEP 7: After charging, check level of electrolyte and
add as needed to bring fluid to proper level.
STEP 8: Reinstall cell caps.
STEP 9: Install battery into power unit.
STEP 10: Both bolts are already installed on both
terminals. Connect positive (+) cable (red) first, from
wiring harness to the positive terminal (+) on battery and
secure with nut provided in hardware bag. Connect
negative (-) cable (black) last, to negative terminal (-) on
battery and secure with nut also provided. Apply a small
amount of grease over terminals to prevent corrosion.
See Figure 1.
WARNING
Shield the positive terminal with terminal cover
located on battery harness. This prevents metal
from touching the positive terminal, which could
cause sparks.
FIGURE 1
STEP 11: Take the necessary precautions, when
handling fuel. Fill the fuel tank with clean fuel. Check oil
and add oil if needed as stated in Engine Owners
Manual. Move fuel tank selector valve handle to the
desired fuel tank.
INSTRUCTION No. 7-5597 (I.R. 4/1/03)
RED (POSITIVE) CABLE
TERMINAL COVER MUST
SHIELD POSITIVE
TERMINAL AFTER
INSTALLATION
BLACK (NEGATIVE) CABLE

Summary

Battery Setup and Charging

Step 1: Remove Machine from Container

Remove the machine from its container; the battery requires charging and installation.

Step 2: Remove Battery for Charging

Take the battery out of its compartment before starting the charging process.

Step 3: Battery Placement

Place the battery in a well-ventilated area on a level, non-concrete surface.

Step 4: Fill Battery Cells

Remove cell caps and fill each cell with electrolyte to the proper level.

Step 5: Connect Battery Charger

Connect the battery charger to the battery terminals, red to positive and black to negative.

Step 6: Slow Charge Battery

Slow charge the battery at 2 amps for 2 hours to achieve a full charge.

Step 7: Check Electrolyte Level After Charging

After charging, verify and adjust electrolyte levels to the proper mark.

Step 8: Reinstall Cell Caps

Place the cell caps back onto the battery after verifying the electrolyte level.

Step 9: Install Battery into Power Unit

Install the charged battery into the designated power unit compartment.

Step 10: Connect Battery Cables

Connect positive cable first, then negative cable. Apply grease to terminals.

Step 11: Fuel and Oil Check

Fill fuel tank with clean fuel, check oil level, and set fuel tank selector valve.

Mower Deck Leveling and Tracking Adjustment

Step 12: Mower Deck Adjustment (Levelness)

Adjust mower deck side-to-side and front-to-rear for proper levelness and pitch.

Step 13: Hydraulic Oil Reservoirs Check

Check and fill hydraulic fluid reservoirs to the correct level using specified oil.

Step 14: Tracking Adjustment - Twin Stick Controls

Adjust machine tracking using twin stick controls if it does not drive straight.

Hydraulic System Purging Procedure

Step 15: Hydraulic System, Purging

Perform procedure to purge air from hydraulic drive systems if pulling issues occur.

Pre-Operation Checklist

Snapper Z-rider Specifications

General

Brand	Snapper
Model	Z-rider
Category	Lawn Mower
Language	English