Solatube 160 DS - Warning; Electrical Components; Re-Roofing; Daylighting Systems Installation Tips

For the most current Installation Instructions, please visit www.solatube.com/instructions
Solatube International, Inc. | 2210 Oak Ridge Way | Vista, CA 92081-8341 | www.solatube.com | T: 888.SOLATUBE
© 2014 Solatube International, Inc. Part No. 951780 v2.7
2
WARNING
Daylighting Systems Installation Tips
These instructions are a step-by-step guide for the installation of a Solatube Daylighting System in the following conditions.
For other roof types, please contact your Solatube International representative for additional information.
Built Up Flat Roof - Single Ply/Membrane - Asphalt Shingle - Low/No Pitched - Pitched -
Prefabricated Curbs - Metal Roof Panels
Please refer to the installation tips for the appropriate product below:
Do not proceed with the installation until you have read the entire instructions, including these warnings.
(Use of materials or methods not authorized by Solatube International will result in an invalid warranty.)
Solatube International, Inc. (seller) assumes no responsibility or obligation whatsoever for the failure of an architect, contractor, installer, or building
owner to comply with all applicable laws, ordinances, building codes, electrical codes, energy codes, re and safety codes and requirements, roof
warranties and adequate safety precautions. Installation of this product should be attempted only by individuals skilled in the use of the tools and
equipment necessary for installation. Protect yourself and all persons and property during installation. If you have any doubt concerning your competence
or expertise, consult a qualied expert before proceeding.
Install at your own risk!
Solatube product installations may be dangerous and include the potential for death, personal injury and property damage. The hazardous
conditions include but are not limited to the following:
 During installation, the Solatube Daylighting System’s reective tubes may focus sunlight, causing intense heat or re. Remove
protective lm only after the parts have been installed. Prior to and during installation, do not leave tubes in contact with
combustible materials or unattended, especially near direct sunlight. Avoid skin burns.
 Solatube Daylighting System and Solar Star products may have sharp edges. Always wear leather or canvas gloves while handling and installing
products.
 Solatube product installations require climbing and working at dangerous heights, including on ladders, scaffolding, roofs and in attic spaces.
Risk of death, personal injury and property damage may result from a fall, or from falling objects. Use extreme caution to minimize risk of
accidental injury, including, but not limited to the following procedures:
 Clear area below your work space of all people, animals and other items.
 Avoid working on surfaces that are slippery or wet.
 Use foot-wear with excellent traction.
 Use only strong, well supported ladders.
 Work only in calm dry weather.
 When in the attic, ensure that your weight is supported at all times with structurally sound framing; drywall material is not designed to
carry a person’s weight.
 To reduce the risk of re, electric shock, and personal injury, basic safety precautions should always be followed when using electric tools,
including always wearing safety goggles or other suitable eye protection, and ensuring work area is clear of all electrical wires, gas pipes, water
pipes, and other obstacles.
 When working in the attic or other dusty areas, use of a mask or respirator is recommended to avoid lung irritation. Attic spaces may be dark,
conned, and subject to extreme temperatures. Beware of sharp protruding objects. Do not attempt installation without having someone within
range of your voice or close enough to come to your aid if necessary.
 Solatube products are not designed to withstand the weight of a person, tools or other objects. Walking or placing objects on the system could
cause personal injury and property damage. If the product is damaged, the structural capacity may be weakened; therefore the system should
be repaired immediately. For safe installation and use, do not deviate from these installation instructions.
 Additional support is recommended for long vertical and all horizontal tube runs. Review local building requirements and consult with
appropriate building code ofcial for proper material and placement of additional support. Avoid galvanic reaction (corrosion) if dissimilar metals
are used.
Electrical Components
 Before installing, servicing, or cleaning unit, switch power off at service panel and lock service panel to prevent power from becoming switched
on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device such as a tag to the
service panel.
Re-Roong
 Solatube products require special care if removed for re-roong. In order to ensure proper removal and re-installation, please contact your
Solatube International representative.