13Instruction Manual12GGSCD70
8.2 Cleaning the Condenser
If you frequently use your appliance, it is recommended to clean the condenser
approximately once every three months. Be careful not to damage the air condenser. Only
clean with water and never use hard or sharp objects.
Warning! Never operate the appliance without the air condenser installed.
Note:
During drying, water may collect between the window and the seal- this is normal and
doesn’t effect the function of your dryer.
— Ensure the dryer has cooled down after any recent operation.
— Unplug the appliance.
— Residual water may escape, so place an absorbent cloth under the maintenance flap.
— Unlock the maintenance flap and open completely.
— Screw both locking levers towards each other.
— Pull out the air condenser.
— Clean the air condenser completely and drain thoroughly.
— Clean the seals.
— Re-insert the air condenser and re-screw the locking levers.
— Close the maintenance flap until it locks into position.
8.3 Empty the water container
Warning! After each use, the water container should be emptied.
— Hold and pull out the water container using two hands.
— Tilt the water container, pouring out the condensed water in to a sink.
— Re-insert the water container into the appliance.
Note:
If the container requires emptying during operation, the Program will pause and the
icon will flash on the display. Follow the process above to empty the container and
restart the Program by pressing the “Start/Pause” button.
Warning! — Do not drink the condenser water.
— Do not operate the dryer without the water container in place.
8.4 Error Alarms
9. Troubleshooting
Warning! Only authorised technicians can carry out repairs.
Before contacting our customer service team, please refer to the table below to see if your
fault can be fixed by yourself. Should a service technician visit be arranged and its found
there are no faults with the appliance, a call out charge will apply.
Problem Solution
Display isn’t turning on. — Check that the mains plug is inserted and switched on
at the power point.
— Check that a Program is selected on the Program
selection dial.
— Check that the relevant fuse hasn’t blown.
indicator is flashing
— Empty the water container as per the steps in 8.3 within
this user manual.
indicator is flashing
— Clean the air cooler.
— Clean lint filter.
Dryer doesn’t start — Check the start button has selected.
— Check the appliance door has closed.
— Check that the Program has been set.
Water is running out of the
dryer
— Align dryer horizontally.
— Clear air condenser and door seals.
Door is opening by itself — Press the door door closed until it “clicks” into position.
— Ensure that the dryer hasn’t been overloaded with
clothes.
Humidity within the room is
increased significantly
— Ensure the room has adequate ventilation.
— Clean the cool vent grill.
— Ensure that the air condensor has been inserted.
Degree of dryness was not
reached or drying time too
long.
— Clean the lint filter and wash the condenser.
— Empty the water container.
— Clean the moisture sensors.
— Try using a higher drying Program next time.
Note:
If the above steps don’t resolve your issue or you cannot resolve the fault by yourself:
— Press the “On/Off” button,
— Switch off the appliance at the power outlet and remove the plug,
— Call our customer service team.
10. Technical Data
Power supply 220-240V ~50Hz
Rated input Power 2000W
Ambient temperature +5°C - + 35°C
Dimensions 595 x 615 x 845 mm
Rated drying capacity 7.0kg
Net Weight 42kg
Note:
— The rated capacity is the maximum capacity of dry clothes. Refer to the Program table for
maximum loadings specific to each Program.
— Do not install the dryer in a room where there is a risk of a frost occurring. At
temperatures around freezing point, the dryer may not be able to operate properly.
— There is a risk of damage if the condensed water is allowed to freeze in the pump, or
water container.
Troubleshooting
To Next Page
Loading...
