EN
EL
5141230A
IZYMO TRANSMITTER io F/CE/NE/SE
IZYMO Transmitter io
Ref.: 1822609A
The transmitter micro-module allows a switch or push-button
to be transformed into an io-homecontrol transmitter (lighting
or roller shutter). It also allows a scenario programmed into the
TaHoma interface to be activated via any push-button.
GENERAL INFORMATION
Read this installation guide and the safety instructions carefully before
installing this Somfy product. All the instructions given must be followed
closely and this guide must be stored in a safe place throughout the service
life of your product. Before installation, check that this Somfy product is
compatible with the associated equipment and accessories.
These instructions describe the installation and use of this product. Any
installation or use outside the field of application specified by Somfy is
forbidden. This invalidates the warranty and discharges Somfy of all liability,
as does any failure to comply with the instructions given herein.
Somfy cannot be held responsible for changes to norms or standards
occurring aer the publication of these instructions.
GENERAL SAFETY INSTRUCTIONS
Children must not be allowed to play with the transmitter. Never immerse
the transmitter in liquid.
This product is not designed to be used by persons (including children)
with reduced physical, sensory or mental capacities, or persons lacking
in experience or knowledge, unless they have received, from a person
responsible for their safety, monitoring or prior instruction regarding the use
of the product.
⚠ Do not connect this product to the mains.
230 V
Risk of explosion if the battery is replaced by an
incorrect type. Do not swallow the battery. If swallowed, the battery can
cause chemical burns in only 2 hours and may be fatal. If
swallowed, call a doctor immediately.
Do not throw onto a fire.
CONDITIONS FOR USE
Do not use this product outdoors. The radio range is limited by the radio
appliance control standards. The transmitter range is heavily dependent on
the environment in which it is used: interference may be caused by having
large-scale electrical equipment near the installation and by the type of
material used in the walls and partitions. The use of a radio appliances (e.g. a
set of Hi-Fi radio headphones) operating on the same radio frequency might
be detrimental to the product’s performance.
CONFORMITY
Somfy hereby declares that the radio equipment covered by these
instructions is in compliance with the requirements of the Radio
Directive 2014/53/EU and the other essential requirements of the
applicable European Directives.
The full text of the EU Declaration of Conformity is available at
www.somfy.com/ce.
WARRANTY
This product is guaranteed for 3 years from the date of purchase.
DESCRIPTION OF THE TRANSMITTER
PROG 1
S2
S1
COM
M
5135173A
PROG 2
MODE
Somfy
F-74300
Cluses
MODE selector
Red MODE LED
Green RADIO LED
Channel 2 PROG button
Channel 1 PROG button
Orange LED
Low battery
Control 2 (yellow)
Modes 3 and 4: up
Control 1 (green)
Modes 3 and 4: down
Common (white)
I- SELECTING THE CONTROL MODE
The transmitter is set to mode 1 (push-button) by default.
To select a mode, push the MODE button on the transmitter briefly
several times until you obtain the desired mode.
Mode 1
Push-button light / scenario
Mode 2
Switch light
PROG 1
S2
S1
COM
M
5135173A
PROG 2
MODE
Somfy
F-74300
Cluses
PROG 1
S2
S1
COM
M
5135173A
PROG 2
MODE
Somfy
F-74300
Cluses
PROG 1
S2
S1
COM
M
5135173A
PROG 2
MODE
Somfy
F-74300
Cluses
PROG 1
S2
S1
COM
M
5135173A
PROG 2
MODE
Somfy
F-74300
Cluses
PROG 1
S2
S1
COM
M
5135173A
PROG 2
MODE
Somfy
F-74300
Cluses
PROG 1
S2
S1
COM
M
5135173A
PROG 2
MODE
Somfy
F-74300
Cluses
PROG 1
S2
S1
COM
M
5135173A
PROG 2
MODE
Somfy
F-74300
Cluses
PROG 1
S2
S1
COM
M
5135173A
PROG 2
MODE
Somfy
F-74300
Cluses
Mode 3
Roller shutter
Mode 4
External venetian blind
PROG 1
S2
S1
COM
M
5135173A
PROG 2
MODE
Somfy
F-74300
Cluses
PROG 1
S2
S1
COM
M
5135173A
PROG 2
MODE
Somfy
F-74300
Cluses
PROG 1
S2
S1
COM
M
5135173A
PROG 2
MODE
Somfy
F-74300
Cluses
PROG 1
S2
S1
COM
M
5135173A
PROG 2
MODE
Somfy
F-74300
Cluses
PROG 1
S2
S1
COM
M
5135173A
PROG 2
MODE
Somfy
F-74300
Cluses
PROG 1
S2
S1
COM
M
5135173A
PROG 2
MODE
Somfy
F-74300
Cluses
PROG 1
S2
S1
COM
M
5135173A
PROG 2
MODE
Somfy
F-74300
Cluses
PROG 1
S2
S1
COM
M
5135173A
PROG 2
MODE
Somfy
F-74300
Cluses
Once the mode has been selected, wait 2 seconds. The indicator
light flashes 3 times to confirm that the mode selected has been
memorised.
The mode selected applies to both channels (S1 and S2).
II- ASSOCIATING THE TRANSMITTER
Associating the first transmitter with an io receiver
1- To activate association mode, consult the receiver instructions.
2- Associate the transmitter: briefly press the PROG 1 button (for
channel S1) or PROG 2 button (for channel S2) on the transmitter.
• The green light flashes on the transmitter.
• The receiver exits association mode.
• The transmitter is now associated with the receiver.
Associating a transmitter with an io receiver
1- Set the receiver to association mode: press the PROG 1 or PROG 2
button on the transmitter for 2 seconds
2- Associate the transmitter:
briefly press the PROG 1 button (for channel S1) or PROG 2 button
(for channel S2) on the transmitter.
• The green light flashes on the transmitter.
• The receiver exits association mode.
• The transmitter is now associated with the receiver.
Associating a transmitter with a TaHoma (scenario)
1- Click on the icon on the PC interface or TaHoma tablet and
then on the configuration menu
.
2- Select the io-homecontrol thumbnail then click on “add”.
3- Select the final type of equipment, “controls”.
4- Then follow the instructions displayed on the screen.
III- INSTALLING THE TRANSMITTER
The transmitter must be installed in the switch housing.
⚠ If one of the wires is not connected, please ensure that it is
insulated or leave rubber tube on.
IV- USE CASE
Light ON-OFF Light variation
Mode 1 Mode 2 Mode 1
Type of control
Channel
S1
S2
S1
COM
S1
COM
S2
S1
COM
S1
COM
-
S2
S1
COM
S2
S1
COM
PROG 1
S2
S1
COM
M
5135173A
PROG 2
MODE
Somfy
F-74300
Cluses
KByyww
EVB
M
M
S2
S1
COM
S1
COM
S2
S1
COM
S1
COM
-
S2
S1
COM
S2
S1
COM
PROG 1
S2
S1
COM
M
5135173A
PROG 2
MODE
Somfy
F-74300
Cluses
KByyww
EVB
M
M
S2
S1
COM
S1
COM
S2
S1
COM
S1
COM
-
S2
S1
COM
S2
S1
COM
PROG 1
S2
S1
COM
M
5135173A
PROG 2
MODE
Somfy
F-74300
Cluses
KByyww
EVB
M
M
S2
S1
COM
S2
COM
S2
S1
COM
S2
COM
-
S2
S1
COM
S2
S1
COM
PROG 1
S2
S1
COM
M
5135173A
PROG 2
MODE
Somfy
F-74300
Cluses
KByyww
EVB
M
M
S2
S1
COM
S2
COM
S2
S1
COM
S2
COM
-
S2
S1
COM
S2
S1
COM
PROG 1
S2
S1
COM
M
5135173A
PROG 2
MODE
Somfy
F-74300
Cluses
KByyww
EVB
M
M
S2
S1
COM
S2
COM
S2
S1
COM
S2
COM
-
S2
S1
COM
S2
S1
COM
PROG 1
S2
S1
COM
M
5135173A
PROG 2
MODE
Somfy
F-74300
Cluses
KByyww
EVB
M
M
Actions
Short press:
ON/OFF
Double press:
ON general
Rocker:
ON/OFF
Short press:
Last value/OFF
Long press:
Variation in the opposite
direction to the last
command.
Double press:
ON 100%
Roller shutter
Exterior
venetian
blind
Scenario
Mode 3 Mode 4 Mode 1
Type of control
Up
S2
S1
COM
S1
COM
S2
S1
COM
S1
COM
-
S2
S1
COM
S2
S1
COM
PROG 1
S2
S1
COM
M
5135173A
PROG 2
MODE
Somfy
F-74300
Cluses
KByyww
EVB
M
M
S2
S1
COM
S1
COM
S2
S1
COM
S1
COM
-
S2
S1
COM
S2
S1
COM
PROG 1
S2
S1
COM
M
5135173A
PROG 2
MODE
Somfy
F-74300
Cluses
KByyww
EVB
M
M
S2
S1
COM
S1
COM
S2
S1
COM
S1
COM
-
S2
S1
COM
S2
S1
COM
PROG 1
S2
S1
COM
M
5135173A
PROG 2
MODE
Somfy
F-74300
Cluses
KByyww
EVB
M
M
S2
S1
COM
S1
COM
S2
S1
COM
S1
COM
-
S2
S1
COM
S2
S1
COM
PROG 1
S2
S1
COM
M
5135173A
PROG 2
MODE
Somfy
F-74300
Cluses
KByyww
EVB
M
M
S2
S1
COM
S1
COM
S2
S1
COM
S1
COM
-
S2
S1
COM
S2
S1
COM
PROG 1
S2
S1
COM
M
5135173A
PROG 2
MODE
Somfy
F-74300
Cluses
KByyww
EVB
M
M
Actions
Press and hold:
Up/Down (stops
when released)
Rocker:
Up/Down until
end limit
Short press:
Tilt slats
Long press:
Up/Down until
end limit
Short press:
Start 1 (or 2)
scenario(s)
defined via
TaHoma
V- DELETING THE TRANSMITTER
Deleting a transmitter from an io already associated
1- Set the receiver to association mode.
2- Briefly press the PROG 1 or PROG 2 button on the transmitter for
the channel to be deleted (channel S1 or S2): the transmitter and
receiver are no longer associated.
Deleting a transmitter via TaHoma
1- Click on the icon on the PC interface or TaHoma tablet and
then on the configuration menu
.
2- Select the io-homecontrol thumbnail then click on the control to
be deleted.
3- Click on “delete”.
4- Then follow the instructions displayed on the screen.
VI- MISCELLANEOUS
Battery life
From 4 years (20 actions/day) to 7 years (2 actions/day).
Battery low information
• Via the transmitter:
When the transmitter battery falls below the critical threshold, the
transmitter only sends a radio command every second activation of
the push-button / switch.
Furthermore, the orange “battery low” LED is lit every time the
button/switch is activated.
• Via the TaHoma interface:
When the transmitter is associated with an io micro-module receiver,
itself associated with TaHoma, a message appears close to the
receiver icon when the transmitter battery is low.
The remaining battery life following this warning is approximately
one month.
Replacing the battery
Replace the old battery with CR2430 battery, respecting the polarity
as shown on the product.
Recycling
• We care about our environment. Do not dispose
of the appliance with the household waste.
• Take it to the relevant collection point for recycling.
• Please separate the battery from other types of waste and
recycle it via your local collection system.
TECHNICAL DATA
Power supply CR2430 battery: 3V
Battery life 3 years
Protection class IP 20
Dimensions 35 x 43 x 8 mm
Radio frequencies
Radio power
868.70MHz - 869.20MHz
e.r.p < 25 mW
Range in open space 200 m
Range through two concrete walls 20 m
Operating temperature 0 °C to +55 °C
Humidity 85% HR at 25°C
SOMFY ACTIVITES SA
50, avenue du Nouveau Monde, F-74300 CLUSES
www.somfy.com
Copyright © 2018 SOMFY ACTIVITES SA, Société Anonyme. All rights
reserved. Capital 35.000.000 Euros, RCS Annecy, 303.970.230 -
06/2018.
Images are not contractually binding