Left and Right
LCR Speakers
6’-10’
4’-15 From Speakers
Overhead View
(1.8m - 3m)
Apart
TV
INTRODUCTION
Thank you for purchasing MAG Concealed TV Audio System.
When properly installed your new speakers will give you
years of entertainment pleasure.
BOX CONTENTS
MAG Concealed TV Audio System box contains:
(2) MAG6 LCR Speakers
(1) SONOS AMP
(1) SONANCE TV Box and Mounting Bracket
(2) SONANCE TV Box Spacers
(1) Power Bridge ONE-CK Power Wall Box
(1) Power Strip with USB
(1) Mounting Screws and Velcro Kit
(2) Wire Grommets
TOOLS NEEDED:
1. Electric Screw Driver
2. Tape Measure
3. Level
4. Stud Finder
5. Drywall Saw
6. Wire Strippers
7. Pencil
TOOLS RECOMMENDED:
1. Steel Fish Tape or Fish Rods
2. Hole Saw or Spade Bits
NEEDED ITEMS:
1. Speaker Wire
BEFORE INSTALLATION
Determine the location for the speakers and Wall Box
(see before you begin below).
Perform an obstruction survey using a stud finder to be
certain that there are no studs, conduit, pipes, heating,
ducts, pocket doors or air returns in the wall cavity that
will interfere with the speaker or SONANCE TV Box.
If you are unsure about obstructions, drill a small hole in
the center of the outline and insert a coat hanger wire
into the hole to feel around for possible obstructions.
NOTE: CONSULT LOCAL BUILDING CODES BEFORE RUNNING
AC WIRES AND SPEAKER WIRES THROUGH WALLS.
MAG PREMIUM SPEAKER PLACEMENT
MAG6 LCR - Left & Right Speakers
1. Place the left and right speakers 6 – 10 feet (1.8m – 3m) apart
from each other. SONANCE recommends installing the center
of the speakers as close to the center the TV, ideally at ear
level when seated. See Figure 1
2. The main listening position should be 4 – 15 feet (1.2m – 4.5m)
away from the speakers and TV.
3. Once you have identified the desired mounting location
and have checked for obstructions, use the included cutout
template and a level to mark the cut lines for the speaker
mounting hole. Then, cut the mounting hole using a drywall
saw, see the template provided with the speakers for cut
out dimensions.
BEFORE YOU BEGIN
Plan your layout of your TV, TV bracket, SONANCE TV Box
and Speakers before cutting any holes.
1. IMPORTANT: Determine the final location where you want
your TV when the install is complete, this will determine
were you place the TV bracket, SONANCE TV Box and
the Speakers.
2. Once you have determined the final install location of where
your TV will be installed measure and mark o with tape the
top and the bottom of where the TV will be installed.
3. Measure from the top and bottom of the marked location to
determine the center location of the TV when mounted and
mark the center location with tape on each side of the TV.
4. Install the TV bracket arms onto the TV, measure and
determine where to mount the TV braket so the TV hangs
in the final location you have previously measured in step
2. Mark the location of the TV bracket.
5. Once you have determined where your TV bracket will
be installed, determine if the SONANCE TV Box will
be installed above or below the TV bracket to best
conceal the SONANCE TV Box but still allows access to
electronics when the TV is installed.
6. Mark the location of the SONANCE TV Box.
7. For more assistance; watch the setup videos by scanning
the QR code on the front cover.
SONANCE TV BOX PLACEMENT
SONANCE TV Box (Figure 2)
• Determine The center location of your television first.
• The SONANCE TV Box is designed to be installed between
two studs. If the center of your TV Covers a stud, position the
SONANCE TV Box to the left or right of the center stud.
Figure 1
3
Centered Oset
Sonancet TV Box installs behind your TV
Outline indicates your TV
Sonance TV Box installs behind your TV
Outline indicates your TV
Figure 2
To Next Page
Loading...
