What to do if there is no audio in zone on my Sonance DAB1?
If you're experiencing a lack of audio in a specific zone of your Sonance Stereo System, ensure the speakers are properly connected and the zone is turned on. Also, verify that the zone volume is turned up. Use the Program Manager to check the Zone's maximum volume and turn-on volume settings. Finally, confirm that the zone is correctly set up in the software.
How to troubleshoot Sonance DAB1 when it will not power up?
If your Sonance Stereo System fails to power up, ensure the DAB Controller is plugged into an un-switched AC outlet and the power cord is securely connected to the DAB1 Controller.
Why DAB1 remote does not control the DAB1 Sonance Stereo System?
If the DAB1 remote is not controlling the DAB1 Sonance stereo system, verify that the zone to be controlled from the front panel of the DAB Controller is selected in Program Manager under Device>General Setup. If that doesn't work, remove the batteries from the remote, wait approximately 10 seconds, and then reinstall them, using only alkaline batteries. Also, try to keep the remote off static surfaces like carpet or rugs.
What to do if there is no audio from source on Sonance DAB1 Stereo System?
If you are experiencing no audio from a source connected to your Sonance Stereo System, first ensure that the source is turned on and playing. Then, verify that the source line audio out is connected to the appropriate source input on the DAB Controller.
How to unlock Sonance Stereo System when no button functions work?
If your Sonance stereo system unit is locked up and no buttons are working, turn off all components and unplug them from the AC outlet, then disconnect the speakers. Unplug the unit’s AC power cord, wait about 15 seconds, and then reconnect it to the appropriate AC outlet.
Why DAB1 Remote does not control source components of Sonance Stereo System?
If the DAB1 Remote is not controlling source components, check that the IR emitters are attached over the IR eyes on the front of the source components and properly plugged into the DAB1. Also, ensure that IR commands for source components have been associated with DAB Remote commands (Stop, Play, Pause, Skip Rev, Skip Fwd) by source and by zone in Program Manager.
What to do if source does not respond to IR command output by DAB Controller of Sonance Stereo System?
If a source is not responding to an IR command output by the DAB Controller of your Sonance stereo system, verify in Program Manager that the proper command has been programmed to a button. Test the IR Command from the IR Library to confirm it is the right code. If necessary, try another remote from the same brand/component. If no codes from the library work, teach the IR command to the IR Library or relearn the command.
Why there is no sound from tuner on Sonance Stereo System?
If there is no sound from the tuner on your Sonance Stereo System, move the Tuner switch on the rear panel to Internal Tuner. Also, check to make sure the antennae is connected.
What to do if there is no paging signal in zones on Sonance DAB1?
If there is no paging signal in zones of your Sonance Stereo System, be sure the Paging audio source is connected to the Page IN jack on the Primary DAB Controller. Also, ensure that Page IN/OUT are connected in an expanded system (multiple DAB Controllers). Verify that the 12V Page Trigger input is connected and that the Page Trigger device is outputting 6-12V AC/DC.
How to fix keypads 4-6 when they will not power up on Sonance DAB1 Stereo System?
If keypads 4-6 are not powering up on your Sonance Stereo System, switch the keypad power switch on the DAB Controller back panel to internal.
General| Subwoofer Output | Yes |
|---|---|
| Wireless | No |
| Amplifier Class | D |
| Digital Audio Inputs | Optical |
| Analog Audio Inputs | RCA |
| Inputs | Optical, RCA |
General safety guidelines for operating the appliance.
Describes the front and rear panels, controls, and indicators of the DAB1 Controller.
Explains the front/rear panels of keypads and the functions of the remote control.
Guides users through the initial setup and testing of a basic six-zone system.
Discusses system expansion, head end, and zone considerations for optimal design.
Guidance on selecting a location, mounting, and ensuring proper airflow for the DAB1 Controller.
Details on wiring keypads using CAT5 cable and RJ45 connectors.
Wiring for Paging, RS232, and Net Control Port connections.
Guides on connecting source components to the DAB1 Controller inputs.
Details on connecting IR emitters and DAB1 keypads.
Procedures for connecting line outputs to amplifiers for high power or sub-zone expansion.
Guides on configuring keypad source buttons, backlighting, and IR receiver settings.
Instructions on how to download the DAB1 Program Manager software from the Sonance website.
Procedures for entering job information and configuring general system settings.
Instructions for setting up AM/FM tuner presets, names, and frequencies.
Guides on setting source names and adjusting volume offsets for balanced output levels.
Procedures to check, download, and install firmware updates for the DAB1 Controller.
Details the File, Remote, Options, and Help features of the IR Library Manager.
Explains the Macro Editor window for programming keypad buttons and macros.
Instructions on adding DAB commands and using status tests in macros.
Details on programming RS232 commands and adding time delays into macros.
Instructions on programming repeat steps and IR toggle commands within macros.
Procedures for capturing IR codes from remotes using the DAB1 Controller.
Step-by-step guide for programming the DAB1 Controller using the Program Manager software.
Guides on configuring zone-specific settings like paging, party mode, volume, and EQ.
Guides on setting source names and adjusting volume offsets for balanced output levels.
Explains the three levels of keypad programming: Press, Press and Hold, and Double Press.
Programming instructions for CD players and satellite receivers.
Explains the use of numeric buttons for tuner presets and programming the OFF button.
Details the RS232 port, commands, syntax, and status queries for controlling the DAB1.
Guides on copying buttons, downloading devices, and managing expanded systems.
Solutions for problems related to system power, keypads, and tuner functionality.
Solutions for problems with IR control, remote functionality, and RS232 communication.
Describes default operation of sources, volume, mute, and off functions.
Information on how to contact Sonance Technical Service for support or repair.
Technical specifications for the amplifier, FM, and AM tuner sections of the DAB1.
To Next Page
