11
Auto On
Select the Auto On method you would like to use with the blue pull
down menu. During setup it is strongly recommended that you
RLLW[OL(\[V6UTL[OVKZL[[V76>,9)<;;65[VWYL]LU[[OL
HTWSPÄLYMYVTZO\[[PUNVќ@V\JHUYL[\YUH[HU`[PTL[V[OL(\[V6U
ZL[[PUNHUKZLSLJ[[OLÄUHSTL[OVKVM(\[V6UMVY`V\YPUZ[HSSH[PVU
>OLUJVU[YVSSPUN[OLHTWSPÄLY\ZPUN07HUK09JVTTHUKZ^L
suggest using the Power Button Auto On mode. See Appendix B.
Audio
In the Audio Auto On mode, there are three sleep mode options
VќTPU\[LZOV\YZ,HJOJOHUULSOHZHUPUKLWLUKLU[ZSLLW
mode setting. The sleep mode is triggered by an audio sensing
JPYJ\P[VULHJOJOHUULSVM[OLHTWSPÄLY;OLTPUPT\TPUW\[ZLUZPUN
level is 0.5mV.
Audio Green
0U[OL(\KPV(\[V6UTVKL[OLHTWSPÄLY^PSSWV^LYVќHM[LY
minutes without an audio signal present on any of the channels.
>OLUHUH\KPVZPNUHSPZHWWSPLK[OLHTWSPÄLY^PSS[HRLHWWYV_PTH[LS`
ZLJVUKZMVY[OLHTWSPÄLY[VYLWYVK\JLH\KPVHM[LYNVPUN
[OYV\NOP[ZWV^LY\WZLX\LUJL0U[OLH\KPV(\[V65TVKL[OL
sleep function is active, see sleep mode note below. This mode
complies with EU energy saving standards.
Power Button
When sleep mode is set to OFF the channel will be on at all times.
Use the sleep mode OFF setting for audio signals like a doorbell or
paging where audio must be reproduced immediately at any time.
Backup Restore
The green BACKUP and RESTORE buttons take all of the settings
VM[OLHTWSPÄLYPUJS\KPUN[OL+:7ZL[[PUNZHUKLUJHWZ\SH[LZ[OLT
PU[VVULÄSL;OPZHSSV^Z`V\[V[YHUZMLY[OLZLZL[[PUNZPU[VHUV[OLY
HTWVM[OLZHTLTVKLS^P[O[OLZHTLÄYT^HYL]LYZPVU;OPZPZH
WYVWYPL[HY`ÄSL[`WLIPUÄSLHNUVZ[PJ[V7*VY4HJ
Print
The print button will output a complete list of all settings for the
HTWSPÄLY0[PZHS^H`ZHNVVKPKLH[VRLLWHIHJR\WOHYKJVW`VM
the settings for each installation.
Voltage
0U[OL=VS[HNL(\[V6UTVKL[OLHTWSPÄLY^PSSWV^LYVќ
immediately when the trigger voltage has been removed. When a
=(*VY+*]VS[HNLPZZLU[[V[OLHTWSPÄLYP[^PSS[HRL
ZLJVUKZMVY[OLHTWSPÄLY[VYLWYVK\JLH\KPVHM[LYNVPUN[OYV\NOP[Z
power up sequence. This mode complies with EU energy
saving standards.
Voltage Green
0U[OL=VS[HNL.YLLU(\[V6UTVKL[OLHTWSPÄLY^PSSWV^LYVќ
immediately when the trigger voltage has been removed. When a
=(*VY+*]VS[HNLPZZLU[[V[OLHTWSPÄLYP[^PSS[HRL
ZLJVUKZMVY[OLHTWSPÄLY[VYLWYVK\JLH\KPVHM[LYNVPUN[OYV\NO
its power up sequence. In Voltage Green mode the Ethernet
JVUULJ[PVUPZUV[HJ[P]L^OLU[OLHTWSPÄLYPZVќ;OPZTVKL
complies with EU energy saving standards.
IP Subnet Mask
The third setting in the IP SETUP section is the IP Subnet Mask.
This is an advanced network setup function. Under most
JPYJ\TZ[HUJLZ[OPZÄLSKZOV\SKUV[ULLK[VILLKP[LK
4HRPUNJOHUNLZPU[OPZÄLSKZOV\SKVUS`ILKVULI`HUL_WLYPLUJL
network administrator.
ID Amp Mode
>OLU[OLWV^LYZ^P[JOPZ[\YULK65[OLWV^LYI\[[VUVU[OL
MYVU[VM[OLHTWSPÄLY^PSSÅHZO[VPUKPJH[L^OPJOHTWSPÄLY`V\HYL
WYVNYHTTPUN;OPZ^PSSTHRL[OLHTWSPÄLYLHZ`[VPKLU[PM`PUHT\S[P
amp installation.
6OHHS0RGH
:SLLWTVKLHSSV^Z`V\[VZLSLJ[OV^SVUN[OLHTWSPÄLY^PSSZ[H`
HJ[P]LHM[LY[OL(\[V65TL[OVKJLHZLZ
6Ɉ
When set in the OFF mode the channel will be on at all times.
Use the OFF setting for audio signals like a doorbell or paging
where audio must be reproduced immediately at any time.
After 15 Minutes
When an audio signal has not been present on a channel for 15
minutes, the channel will go to sleep. From the sleep state the
channel will take approximately 2-3 seconds to reproduce audio
again. This mode is similar to legacy Sonamp Auto-On operation.
After 3 Hours
When an audio signal has not been present on a channel for
3 hours, the channel will go to sleep. From the sleep state the
channel will take approximately 2-3 seconds to reproduce audio
again when audio is detected.. This mode works well for home
theater installations.
Info
;OLVYHUNLISVJRZHYLPUZ[HSSLYLU[LYLKKH[H,HJOÄLSKOHZH
maximum of 15 characters.
To Next Page
Loading...
Need help?
General
