.....
I
N
CX)
Specifications
General
System
CRT
525 lines, 60 fields per second
interlaced
625 lines, 50 fields
per second
interlaced
Super fine pitch Trinitron
BVM-20ElE/20El U/20FlE/
20FlU
Aperture grille pitch: 0.3 mm,
(BVM-20FIE/20FI U)
Aperture grille pitch: 0.25 mm,
(BVM-20EIE/20EI U)
90 degree deflection, 30.6 mm
diameter in-line gun.
Effective picture size:
386x291 mm(l5'/,x
ll'h
inches) (w/h)
482 mm (19 inches) (diagonal
size)
CRT protection:EHf (extremely
high tension) protection type
Warm-up time: approx. 30 minutes
Anode voltage: 27 kV with no
beam current
Nominal chromaticity coordinates:
SMPTE phosphor (BVM-20E 1 U/20F1 U)
X y
A 0.630 0.340
G
0.310 0.595
B
0.155 0.070
Error: less than ±0.005 ·
EBU phosphor (BVM-20E 1 E/20F19)
X y
A
0.640
0,330
G 0.290 0.600
B
0.150 0,060
Error: less than ±0.005
BVM-41ElE/l4El U/14ESE/
14ESU/14Fl E/14Fl U/l 4F5E/
14FSU
Aperture grille pitch: 0.25 mm
(BVM-14FIE/14FIU/14F5Ei
14F5U)
Aperture grille pitch: 0.22 mm
(BVM-14EIE/14EIU/14E5E/
14E5U)
90-degree deflection,
29.4 mm
diameter in-line gun.
Effective picture size:
268 x 201mm (10
5
/,
x 8 inches)
(w/h)
332 mm (
13 1/8 inches) (diagonal
size)
CRT protection:
EHf (extremely
high tension) protectiontype
Warm-up time: approx. 30 minutes
Anode voltage: 25 kV with no
beam current
Nominal chromaticity coordinates:
SMPTE phosphor (BVM-14E1U/
14E5U/14F1 U/14F5U)
X y
A
0.630
0.340
G
0.310
0,595
B
0.155
0.070
EBU phosphor (BVM-14E 1 E/14E5E/
14F1E/14F5E)
X y
A
0.640
0.330
G
0.290
0.600
B
0,150 0.060
Power requirements
100 to 240 V AC, ±10%, 50/60 Hz
Power consumption
BVM-20EIE/20EI U/20FIE/
20FlU: 120W
BVM-14EIE/14EI U/14E5E/
14E5U/14FIE/14FIU/
14F5E/
14F5U: 110W
Dimensions BVM-20EIE/20EIU/20FIE/
20FlU: 444
X 414 X 570 mm
(17 'hx 16
3
/,x22 'h
inches) (w/h/d)
BVM-14E5E/14E5U/14F5E/
14F5U: 482
x 280 X 580 mm
(19
x II¼ x 20 'la inches)
(w/h/d)
BVM-14EIE/14EIU/14FIE/
14FIU: 346
X 280 X 530 mm
(13
5
/,
x I I¼ x 20 'la inches)
(w/h/d)
Dimensional drawing
BVM-20ElE/20ElU/20FlE/20FlU
Unit mm Qnches)
444
(17
1
/2)
I
410 (16
1
/,4)
. - - -~,
I
--~
c,,,]
&!:!.
.
•
g
I
'}
•
g
g
g
~
•
g
Iii
•
'" llEll
G
IA
0
0
~~
r-r-r-30 (
13
11&)
30 (13/1e)-r----t-
"'"'
~1
~
26 (11/uJ) 26(
11
1,e)~
BVM-14ElE/14ElU/14FlE/l4FlU
Mass
i~
mw
Unit mm (Inches)
33~
BVM-20EIE/20EIU/20FIE/
20FIU: approx. 37 kg (81 lb
9oz)
BVM-14E5E/14E5U/14F5E/
14F5U: approx. 25 kg
(55 lb
I oz)
BVM-14EIE/14EIU/14FIE/
14FIU: approx, 22 kg (48 lb
8 oz)
Input/output Connectors
Video input
BNC type, 3 (with three loop-
through outputs)
R/G/8: I Vp-p
±6 dB, positive,
high impedance
Y: I Vp-p
±6 dB, positive, high
impedance
R-Y/8-Y: 0.7 Vp-p
±6 dB,
positive, high impedance
Sync input BNC type, I (with loop-through
output)
Composite sync:
0.3 to 8 Vp-p,
negative, high impedance
Return loss More than 46 dB
(7 MHz, with 75-
ohm termination)
Remote control OPTION
Video Signal
Mini-DIN 8-pin,
CONTROL UNIT
D-sub 9-pin,
REMOTE I
D-sub 9-pin, I (with loop-
through output), RS-485 serial
interface
REMOTE2
D-sub 9-pin, I (with loop-
through output)
ISR
D-sub 9-pin, I
Differential gain Less than 2% (for luminance from
0 to I 00 cd/m
2
)
Differential phase Less than 2· (for luminance from 0
to I 00 cd/m')
Frequency response
100 Hz to 10 MHz, ±I dB
DC restoration Back porch type
Black level fluctuation: less than
I% for 10 to 90% APL input
signal variation.
Synchronization
AFC time Constant
0.5 ms (fast mode)
2 ms (normal mode)
Line pull range/line hold range
Greater than
±500 Hz (with 0.5 ms
AFC time constant)
Vertical blanking time
Normal: less than I ms.
Underscan: less than 0.8 ms
Horizontal blanking time
Less than 10
µs
To Next Page
Loading...
