Sony CFD-G770CP - Basic Operations

7
CFD-G700CP/G770CP/G770CPK
CFD-G770CP (1/2)
Basic Operations
*VOL + (VOLUME + on the remote)
ȱ
, ā
ȯ
and à
Ȫ
(on the
unit) have a tactile dot.
Before using the unit
To turn on/o the power
Press POWER
ȩ
.
To adjust the volume
Press VOL +, – (VOLUME +, – on the remote)
ȱ
.
To listen through headphones
Connect the headphones to the  (headphones) jack Ȼ.
To select the sound characteristic
Press ROCK, DANCE, SALSA, REGGAETON or FLAT
ȫ
to select the kind of audio emphasis that you want.
(On the remote, press SOUND
ȫ
repeatedly.)
To reinforce the bass sound
Press POWER DRIVE WOOFER (WOOFER on
the remote)
ȷ
to select or on
the display.
is more eective. When the
WOOFER function works, the ring on the front panel
lights up.
To re tur n to normal sound, press the button repeatedly
until the indication disappears from the display.
Notes
ˎ
While the sleeping timer is on, the ring does not light, even if the
WOOFER function is used.
ˎ
When you use the headphones, the WOOFER function does not
work.
Playing a CD/MP3 disc
1 Press ì PUSH OPEN/CLOSE
Ȱ
on the unit, and
place a disc with the label side up on the CD
compartment.
To close the CD compartment, press ì PUSH OPEN/
CLOSE
Ȱ
on the unit.
2 Press
ā
on the unit (
à
on the remote)
ȯ
.
e unit plays all the tracks/MP3 les once.
When you place MP3 discs, “MP3” appears in the
display aer the unit reads the le information.
Audio CD
Track number Playing
time
MP3 disc
MP3 le number After the song title is displayed,
the playing time* will appear.
*If the playing time is more than 100 minutes, it appears “--:--” in
the display.
To P ress
Pause playback
ā on the unit ( ê on the remote)
ȯ . To resume play, press it again.
Stop playback
Ą ȯ .
Go to the next
track/MP3 le
Ñ Ȯ .
Go back to the
previous track/
MP3 le
à Ȯ .
Select a folder on
an MP3 disc
+ to go forward and – to go
backward
ȭ
.
Locate a point
while listening to
the sound
Ñ (forward) or à (backward)
Ȯ while playing and hold it until
you nd the point. (
ù or ß ȿ
on the remote)
Locate a point
while observing
the display
Ñ (forward) or à (backward)
Ȯ in pause and hold it until you
nd the point. (
ù or ß ȿ on
the remote)
Remove the CD
ì PUSH OPEN/CLOSE Ȱ .
Tips
ˎ
Playback starts from the track/MP3 le you last stopped playing
(Resume play). During stop, the track/MP3 le number to be played
is displayed.
ˎ
To cancel the resume play (to start play from the beginning of the
rst track/MP3 le), press
Ą
ȯ
while the CD is stopped. When you
open the CD compartment or turn o the unit, the resume play is
also canceled.
Note
Yo u cannot locate a specic track if “SHUF” or “PGM” is lit in the
display.
Press
Ą
ȯ
, and then press MODE
ȵ
repeatedly until “SHUF” and
“PGM” disappear from the display.
Example of folder structure and playing order
e playing order of the folders and les is as follows:
Folder
MP3 le
Notes on MP3 discs
ˎ
When the disc is inserted, the unit reads all the les on that disc.
During this time, “READING” is displayed. If there are many folders
or non-MP3 les on the disc, it may take a long time for play to
begin or for the next MP3 le to start play.
We recommend that you do not save unnecessary folders or les
other than MP3 ones in the disc to be used for MP3 listening.
ˎ
A folder that does not include an MP3 le is skipped.
ˎ
Maximum number of les: 255
Maximum number of folders: 150 (including the root folder)
Maximum number of folders and les in total: 256
Maximum directory levels: 8
ˎ
Folder names and le names can be displayed with up to 30
characters including quotation marks.
ˎ
e characters A - Z, 0 - 9, and _ can be displayed on this unit.
Other characters are displayed as “_”.
ˎ
is unit conforms to Version 1.0, 1.1, 2.2, 2.3 and 2.4 of the ID3 tag
format. When the le has the ID3 tag information, “song title”, “artist
name” and “album name” can be displayed. If the le does not have
the ID3 tag information, “NO TITLE” appears instead of song title,
“NO ARTIST” appears instead of artist name and “NO ALBUM”
appears instead of album name. e ID3 tag information can be
displayed with up to 15 characters.
ˎ
When naming, be sure to add the le extension “mp3” to the le
name.
ˎ
If you put the extension “mp3” to a le other than an MP3 le, the
unit cannot recognize the le properly and will generate random
noise that could damage your speakers.
ˎ
e le name does not correspond to the ID3 tag.
Listening to the radio
1 Press RADIO/BAND
ˎ
AUTO PRESET
Ȭ
on the unit
(RADIO/BAND
Ȭ
on the remote) repeatedly.
Each time you press the button, the indication changes
as follows:
“FM”  “A M ”
2 Hold down TUNE + or –
ȭ
until the frequency
digits begin to change in the display.
e unit automatically scans the radio frequencies and
stops when it nds a clear station.
If you cannot tune in a station, press
TUNE +or–
ȭ
repeatedly to change the frequency step by step.
When an FM stereo broadcast is received, “ST”
appears.
Tip
If the FM broadcast is noisy, press MODE
ȵ
until “Mono” appears in
the display and the radio will play in monaural.
Changing the AM tuning interval
If you need to change the AM tuning interval, do the
following:
1 Press RADIO/BAND
ˎ
AUTO PRESET
Ȭ
on the unit
until “AM” is displayed.
2 Press DSPL/ENT
Ⱥ
on the unit for 2 seconds.
3 Press RADIO/BAND
ˎ
AUTO PRESET
Ȭ
on the unit for
2 seconds.
“9K STEP” or “10K STEP” ashes.
4 Press PRESET + or –
Ȯ
on the unit to select “9K
STEP” for 9 kHz interval or “10K STEP” for 10 kHz
interval.
5 Press DSPL/ENT
Ⱥ
on the unit.
Aer changing the tuning interval, you need to reset your
preset AM radio stations.
Playing a tape
Use buttons on the unit for the operation.
1 Press Ąì
Ȫ
on the unit, and insert the tape into
the tape compartment with the side you want to
play facing upward. Use TYPE I (normal) tape only.
Close the compartment.
Make sure there is no slack in the tape to avoid
damaging the tape or the unit.
2 Press à
Ȫ
on the unit.
e unit starts playing.
To P ress
Pause playback
ê Ȫ on the unit. To resume play,
press it again.
Stop playback
Ąì
Ȫ on the unit.
Fast-forward or
rewind*
ù
or
ß
(rewind or fast
forward)
Ȫ on the unit.
Eject the cassette
Ąì
Ȫ on the unit.
*When the tape is wound to the end, press
Ąì
Ȫ
to release
ù
or
ß
Ȫ
.
Recording on a tape
Use buttons on the unit for the operation.
1 Press Ąì
Ȫ
on the unit to open the tape
compartment and insert a blank tape with the side
you want to record on facing upward. Use TYPE I
(normal) tape only. Close the compartment.
2 Select the program source you want to record.
To re cord from the CD player, press Ą
ȯ
on the unit
and place a CD.
To re cord from the radio, tune in the station you want
(see “Listening to the radio”).
3 Press Ć
Ȫ
on the unit to start recording (
à
is
depressed automatically).
To P ress
Pause recording
ê Ȫ on the unit.
Press the button again to
resume recording.
Stop recording
Ąì Ȫ on the unit.
Tips
ˎ
Adjusting the volume or the audio emphasis will not aect the
recording level.
ˎ
For the best results, use the AC power as a power source for
recording.
ˎ
To erase a recording, proceed as follows:
1Insert the tape whose recording you want to erase.
2Make sure that “TAPE” is displayed. (If “TAPE” is not displayed,
press à
Ȫ
on the unit or press FUNCTION
Ƚ
on the remote
until it appears in the display.)
3Press
Ć
Ȫ
on the unit.