Precaution
11
Reduce the brightness
Reduce the brightness as much as possible or reduce
the input signal level when you do not use the display.
Turn off the power when not in use
Turn off the power if the monitor is not to be used for
a prolonged period of time.
Screen saver
This product has a built-in screen saver function to
reduce burn-in. When an almost still image is displayed
for more than 10 minutes, the screen saver starts
automatically and the brightness of the screen decreases.
Panel Calibration
This product has a Panel Calibration function to adjust
the uniformity of the screen.
It is recommended to perform Panel Calibration once a
week. Perform Panel Calibration in the range of the
recommended environmental temperature (20 °C to 30
°C (68 °F to 86 °F)).
For details, see [Panel Calibration] (page 27).
Perform Panel Calibration when the CALIBR. indicator
lights up in yellow.
Images cannot be displayed when performing Panel
Calibration.
On a Long Period of Use
Due to an OLED’s panel structure and characteristics of
materials in its design, displaying static images for
extended periods, or using the unit repeatedly in a high
temperature/high humidity environments may cause
image smearing, burn-in, areas of which brightness is
permanently changed, lines, or a decrease in overall
brightness.
In particular, continually displaying an image smaller
than the monitor screen, such as displaying an image in
a different aspect ratio or displaying an image with a
frame, may expedite the above issues.
Avoid displaying a still image for an extended period, or
using the unit repeatedly in a high temperature/high
humidity environment such an airtight room, or around
the outlet of an air conditioner.
To prevent any of the above issues, we recommend
reducing brightness slightly, and to turn off the power
whenever the unit is not in use.
On High Brightness Display
Using the unit with the high brightness display for
extended periods may cause eyestrain or reduction of
eyesight. Be sure to take an occasional break when
using.
Follow RECOMMENDATION ITU-R BT.1702
“Guidance for the reduction of photosensitive
epileptic seizures caused by television” or other
guidelines when using.
In the HDR display, the display surface may emit heat
when high brightness images are output. Do not touch
the surface.
When [2.4(HDR)], [S-Log3(HDR)], [S-Log2(HDR)],
[SMPTE ST 2084(HDR)], [HLG SG 1.2(HDR)], or
[HLG SG Variable(HDR)] is selected for [EOTF] in
the [Input Setting] menu, images are displayed in
HDR (High Dynamic Range).
In this manual, this status is described as “HDR
display.”
For details on the HDR (High Dynamic Range) display, see
page 29.
On the Surface of the Unit
The surface of the unit becomes extremely hot. Do not
touch the surface with your hand or body during power
distribution. It may cause a burn.
On Long Periods of Continuous Use
Using this unit for extended periods may cause eyestrain
or reduction of eyesight.
As soon as you feel physical discomfort or pain, stop
using this unit immediately and take a break.
If the physical discomfort or pain remains even after
taking a break, consult a physician.
Handling and Maintenance of the
Screen
The surface of the screen is specially coated to reduce
image reflection. Make sure to observe the following
points as improper maintenance procedures may impair
the screen’s performance. In addition, the screen is
vulnerable to damage. Do not scratch or knock against it
using a hard object.
Be sure to disconnect the AC power cord from the AC
outlet before performing maintenance.
The surface of the screen is specially coated. Do not
attach adhesive objects, such as stickers, on it.
The surface of the screen is specially coated. Do not
touch the screen directly.
Wipe the screen surface gently with the supplied
cleaning cloth or a soft dry cloth to remove dirt.
Stubborn stains may be removed with the supplied
cleaning cloth, or a soft cloth slightly dampened with a
mild detergent solution.
To Next Page
Loading...
