Why the television broadcast displayed with Network Media is lagging the actual broadcast on Sony Stereo Receiver?
When watching television broadcasts with Network Media, there is a signal lag of approximately 15 seconds from the actual television broadcast.
What to do if there is no sound no matter which component is selected on Sony STR-LV700R Stereo Receiver?
If there is no sound from your Sony Stereo Receiver, verify that both the receiver and all connected components are powered on. Ensure that you have selected the correct component on the receiver. Check if headphones are connected, and if so, disconnect them. Make sure the VOLUME control is not set to MIN. Confirm that all speaker cables are correctly connected. Also, press the MUTING button on the remote to deactivate the muting function. If none of these resolve the issue, the protection circuit may be activated. Turn off the receiver, address any short-circuit issues, and then turn the power back on after about 20 seconds.
Why there is no sound from a specific component connected to Sony Stereo Receiver?
If you're not getting sound from a specific component connected to your Sony Stereo Receiver, first, check that the component is correctly connected to the appropriate audio input jacks. Next, ensure that the cables used for the connection are fully inserted into the jacks on both the receiver and the component. Finally, verify that you have selected the correct component on the receiver.
What to do if there is no sound from one of the front speakers of Sony STR-LV700R?
If you're experiencing no sound from one of the front speakers on your Sony Stereo Receiver, try these steps: First, connect headphones to the PHONES jack to check if sound is outputting through them. If only one channel outputs through the headphones, then the component may not be correctly connected to the receiver. Ensure all cables are fully inserted into the jacks on both the receiver and the component. If both channels output through the headphones, the front speaker itself may not be correctly connected to the receiver. In this case, check the connection of the front speaker that isn't producing sound.
Why the multi-channel surround effect of the Dolby Digital or DTS is not obtained on Sony STR-LV700R Stereo Receiver?
If you're not getting the multi-channel surround effect from Dolby Digital or DTS on your Sony Stereo Receiver, ensure that the DVD software or other media is recorded in Dolby Digital or DTS. If you're connecting a DVD player or similar device to the digital input jack, verify the audio settings (specifically for digital audio output) of that component. Also, check that the correct audio track is selected on the DVD player via the DVD menu.
Why there is a delay between pressing the CH +/- buttons and the channel change on Sony Stereo Receiver?
It may take between 3 and 5 seconds for the channel to change after you press the CH +/- buttons.
Why the television screen is dark when using Sony STR-LV700R?
To protect the television tube, if the system is idle for 15 minutes while Network Media is displaying the menu screen or playing music, the screen is automatically darkened (this is not a malfunction). Press a remote button to restore the screen to its normal brightness. To protect the tube, do not leave the menu screen displayed for long periods.
Why there is a delay between pressing the REC button and the start of recording and the same after pressing REC STOP and the end of recording on Sony Stereo Receiver?
It takes approximately 20 seconds before pressing the REC or REC STOP button takes effect. Allow sufficient time to take this into account before you start recording.
Why RDS does not work on my Sony STR-LV700R Stereo Receiver?
If RDS isn't working on your Sony Stereo Receiver, first ensure that you have tuned into an FM RDS station. If you have, try selecting a stronger FM station.
Why there is no sound or only very low-level sound from the surround speakers of Sony STR-LV700R Stereo Receiver?
If there's no sound or only very low-level sound coming from the surround speakers on your Sony Stereo Receiver, first, make sure the sound field function is turned on by pressing the SOUND FIELD button. If that doesn't work, try selecting the CINEMA STUDIO EX mode. Also, adjust the speaker level. Finally, ensure that the surround speakers are set to SMALL or LARGE.
Introduces the receiver's capabilities, including Dolby Pro Logic II and Network Media.
Guides through the initial setup steps for the receiver and Network Media.
Details how to connect various output devices and components to the receiver.
Covers fundamental operations like selecting components, radio tuning, and sound modes.
Covers fundamental operations like selecting components, radio tuning, and sound modes.
Explains how to configure speaker settings and utilize surround sound modes.
Explains how to set up the VAIO computer and Network Media.
Guides on watching video, listening to music, viewing photos, and TV broadcasts.
Covers IP address, software updates, language, and resetting Network Media.
Includes remote details, precautions, specifications, package contents, and button locations.
Explains the functions of various buttons on the remote control.
Important safety, power source, heat, positioning, and cleaning guidelines.
Provides solutions for common problems with the receiver and Network Media.
Lists the technical specifications of the receiver's components.
General| Frequency response | 10 Hz - 100 kHz |
|---|---|
| Weight | 8.5 kg |
| Amplifier Type | Analog |
| Output | Speaker terminals, headphone jack |
| Output Power | 100 W per channel |
| Outputs | Speaker terminals, headphone jack |
| Tuner | FM/AM |
| Remote Control | Yes |
| Dimensions (W x H x D) | 430 x 157.5 x 306 mm |
To Next Page
