What to do if my Sony TV has no picture and no sound?
If your Sony TV has no picture and no sound, ensure that the power cord, antenna, and VCR are properly connected. Also, verify that the TV is turned on by pressing the power button. If it's still not working, try turning the TV off using the main power switch for about five seconds, and then turn it back on.
How to fix no sound on my Sony Trinitron KV-XR29M80 TV but good picture?
If your Sony TV has a good picture but no sound, first, increase the volume level by pressing the volume up button. If that doesn't work, check if the sound is muted and, if so, cancel the muting.
How to fix a snowy picture and noisy sound on Sony Trinitron KV-XR29M80?
If your Sony TV is showing a snowy picture and has noisy sound, check the antenna cable and its connections on the TV, VCR, and at the wall. Ensure the antenna setup is appropriate. If the signal transmission is low, try using a booster. You can also display the “Channel Setup” menu and select “Manual Program” to preset the channel again.
Why does my Sony TV have double images or ghosts?
Double images or “ghosts” on your Sony TV can occur if broadcast signals are reflected by nearby mountains or buildings. Try using a highly directional antenna or the fine tuning function. Also, check the antenna setup and turn off or disconnect the booster if it is in use.
Why does my Sony TV show dotted lines or stripes?
Dotted lines or stripes on your Sony TV can be caused by local interference from things like cars, neon signs, hair dryers, or power generators. Avoid using a hair dryer or other equipment near the TV and check the antenna setup.
What to do if my Sony Trinitron KV-XR29M80 has no color?
If your Sony TV has no color, display the “Picture” menu and select “Personal” of “Mode”, then adjust the “Color” level in “Picture Adjustment.” Check the “Color System” setting in the “Setup” menu and usually set this to “Auto”. Also, verify that the antenna setup is correct.
What causes distorted picture and noisy sound on a Sony Trinitron KV-XR29M80 TV?
Distorted picture and noisy sound on your Sony TV can be caused by broadcast signals that are too strong. If you are using a booster, try turning it off or disconnecting it.
Why does my Sony Trinitron KV-XR29M80 TV have noisy sound with a good picture?
If your Sony TV has a good picture but noisy sound, the TV system setting may be inappropriate. Display the “Channel Setup” menu and select the appropriate “TV System”.
General| Screen Size | 29 inches |
|---|---|
| Display Type | CRT |
| Brand | Sony |
| Model | KV-XR29M80 |
| Type | Trinitron |
| Aspect Ratio | 4:3 |
| Color System | PAL, SECAM, NTSC |
| Input Ports | Component, Composite, S-Video |
Lists diagnostic items, causes, and symptoms based on standby lamp flashes.
Detailed procedure for removing the picture tube.
Procedures for removing and safely handling the anode cap.
Steps to adjust beam landing for proper picture alignment.
Procedure for adjusting color convergence for sharp picture.
How to perform service adjustments using the remote commander.
Procedures to optimize picture quality settings.
Adjusting color balance and levels for different video signals.
Detailed steps for adjusting white balance for different color temperatures.
Procedures for adjusting picture deflection and geometry.
Adjusting various picture distortions for optimal display.
Overall system block diagram showing major functional units and connections.
Detailed schematic for the C board (RGB Amplifier).
Schematic diagram for the A board, Processor block.
Schematic diagram for the A board, Audio block.
Schematic for A board, Power Supply/Deflection block.
Schematic diagram for the A board, Tuner block.
Schematic diagram for the D3 board (Dynamic Focus & DPQ).
Schematic diagram for the VM board (Velocity Modulation).
List of voltage measurements and waveforms for key ICs.
Voltage list and waveforms for IC001 on the A board.
Voltage list for various ICs on the A board.
Important safety information regarding electricity, handling, and environment.
Precautions for preventing fire hazards and ensuring stable installation.
Guides the user through the initial TV setup process.
Explains the functions of each button on the remote control.
How to adjust picture settings like mode, color, and sharpness.
How to adjust sound settings like mode, balance, and volume.
How to preset channels, set TV system, label programs, and block channels.
How to change menu language, picture position, size, and color system.
Common TV problems, their possible causes, and solutions.
Additional troubleshooting steps for picture slant and sound issues.
To Next Page