18
For PVM-14M2E/14M2A:
CRT P-22 phosphor
Power consumption 90 W (with SDI: 99 W)
Power requirements 100 to 240 V AC, 50/60Hz, 1.2–0.5 A
Peak inrush current
(1) Power ON, current probe method: 18 A (240 V)
(2) Hot switching inrush current, measured in
accordance with European standard EN55103-1:
4 A (230 V)
Dimensions (w/h/d) Approx. 346 × 340 × 431 mm
(13
5
⁄8 × 13
1
⁄2 × 17 inches)
not incl. projecting parts and controls
Mass Approx. 16.7kg (36 lb 13 oz)
Accessory supplied AC power cord (1)
AC plug holder (1)
Tally label (1)
Cable with a 20-pin connector (1)
For PVM-20M4U:
CRT SMPTE-C phosphor
Power consumption 125 W (with SDI: 135 W)
Power requirements 120 V AC, 50/60Hz, 1.3 A
Dimensions (w/h/d) Approx. 450 × 458 × 503 mm
(17
3
⁄4 × 18
1
⁄8 × 19
7
⁄8 inches)
not incl. projecting parts and controls
Mass Approx. 30.0 kg (66 lb 2 oz)
Accessory supplied AC power cord (1)
AC plug holder (1)
Tally label (1)
Cable with a 20-pin connector (1)
For PVM-20M4E/20M4A:
CRT EBU phosphor
Power consumption 130 W (with SDI: 140 W)
Power requirements 100 to 240 V AC, 50/60Hz, 1.6–0.6 A
Peak inrush current
(1) Power ON, current probe method: 18 A (240 V)
(2) Hot switching inrush current, measured in
accordance with European standard EN55103-1:
7 A (230 V)
Dimensions (w/h/d) Approx. 450 × 458 × 503 mm
(17
3
⁄4 × 18
1
⁄8 × 19
7
⁄8 inches)
not incl. projecting parts and controls
Mass Approx. 30.0 kg (66 lb 2 oz)
Accessory supplied AC power cord (1)
AC plug holder (1)
Tally label (1)
Cable with a 20-pin connector (1)
Specifications
For PVM-20M2U:
CRT P-22 phosphor
Power consumption 115 W (with SDI: 125 W)
Power requirements 120 V AC, 50/60Hz, 1.2 A
Dimensions (w/h/d) Approx. 450 × 458 × 503 mm
(17
3
⁄4 ×18
1
⁄8 × 19
7
⁄8 inches)
not incl. projecting parts and controls
Mass Approx. 30.0 kg (66 lb 2 oz)
Accessory supplied AC power cord (1)
AC plug holder (1)
Tally label (1)
Cable with a 20-pin connector (1)
For PVM-20M2E:
CRT P-22 phosphor
Power consumption 120 W (with SDI: 130 W)
Power requirements 100 to 240 V AC, 50/60Hz, 1.5–0.6 A
Peak inrush current
(1) Power ON, current probe method: 18 A (240 V)
(2) Hot switching inrush current, measured in
accordance with European standard EN55103-1:
7 A (230 V)
Dimensions (w/h/d) Approx. 450 × 458 × 503 mm
(17
3
⁄4 ×18
1
⁄8 × 19
7
⁄8 inches)
not incl. projecting parts and controls
Mass Approx. 30.0 kg (66 lb 2 oz)
Accessory supplied AC power cord (1)
AC plug holder (1)
Tally label (1)
Cable with a 20-pin connector (1)
Common to all models
Operating temperature
0 to +35°C (32 to 95°F)
Transport and Storage temperature
–10 to +40°C (14 to104°F)
Pressure 700 to 1,060 hPa
Humidity 0 to 90% (no condensation)
Design and specifications are subject to change
without notice.
To Next Page
Loading...