Sony UP-DX100 - User Manual

Other manuals for Sony UP-DX100

Installation Guide8 pages

Questions and Answers

E
Elizabeth LopezDec 1, 2025
What to do if data cannot be transmitted to my Sony UP-DX100?
- N
  nmooreDec 1, 2025
  If data cannot be transmitted to your Sony Printer, consider these potential causes: * The distance between the device and the printer may be too great; locate the devices within the maximum communicable distance. * The Bluetooth antenna portion of the printer and/or the camera may be covered; do not cover the antenna portion. * The device you wish to connect with the printer may already be connected with another device; reconnect the device with the printer after the device’s task with another device is finished. * Authentication may have failed; reconnect the printer with the device, and enter the same passkey correctly on both devices. * The connected device may have interrupted the transmission; check the status of the connected device, then reconnect. * The Bluetooth con...
D
duffymarkAug 25, 2025
What to do if my Sony UP-DX100 says SET PAPER PUSH [EXEC]?
- S
  Samantha MartinAug 26, 2025
  If your Sony Printer displays 'SET PAPER PUSH [EXEC],' it means either the paper tray isn't installed or the print paper has run out. Install the paper tray or insert print paper, and then press the EXEC button.
K
Keith ThompsonAug 27, 2025
What to do if my Sony UP-DX100 Printer says PAPER JAMMING REMOVE PRINTS?
- M
  Marie JonesAug 27, 2025
  If your Sony Printer displays 'PAPER JAMMING REMOVE PRINTS', it indicates a paper jam. Remove the jammed paper and try printing again.
P
Paula MitchellAug 27, 2025
What to do if my Sony UP-DX100 Printer says SET NEW RIBBON PUSH [EXEC]?
- M
  Maria PerezAug 27, 2025
  If your Sony Printer displays 'SET NEW RIBBON PUSH [EXEC],' it means the print cartridge is either not installed properly or has run out. Install the print cartridge properly or replace it, and then press the EXEC button.
B
Benjamin FreemanAug 28, 2025
What to do if my Sony Printer says REMOVE PRINTS PUSH [EXEC]?
- R
  Robert McconnellAug 28, 2025
  If your Sony Printer displays 'REMOVE PRINTS PUSH [EXEC],' it means print paper remains in the ejection slot. Remove the paper tray, remove the print paper, and then press the EXEC button.
R
Ryan HallSep 16, 2025
What causes white lines or dots in printed pictures from my Sony Printer?
- C
  Christopher RamirezSep 17, 2025
  White lines or dots in printed pictures from your Sony Printer can be caused by dust on the thermal head or damage to the print paper by the roller inside the printer. To fix this, use the supplied cleaning cassette to clean the head and path. Also, reduce the number of sheets on the paper tray.
J
joshua94Sep 14, 2025
How to fix slow data transmission speed on Sony Printer?
- T
  Thomas MorrisSep 14, 2025
  If the data transmission speed is too low on your Sony Printer, ensure that the Bluetooth antenna portion of the printer and/or the camera is not covered. Additionally, try changing the position of the printer or setting it closer to the device.
G
George MckaySep 15, 2025
What to do if my Sony UP-DX100 Printer connection is disconnected?
- C
  Corey JacksonSep 15, 2025
  If the connection to your desired device is disconnected from your Sony Printer, it could be due to several reasons. The authentication time limit (30 seconds) might have elapsed, the same passkey might not have been entered, or the device may have disconnected or ended the connection. To resolve this, ensure you enter the same passkey correctly on both the printer and the device within 30 seconds. Also, check the status of the device and try connecting again, making sure to enter the passkey correctly.
A
ashley83Sep 7, 2025
Why does authentication fail on my Sony UP-DX100?
- C
  charlesdeanSep 7, 2025
  Authentication might fail on your Sony Printer because: * The authentication time limit (30 seconds) elapsed. * The same passkey is not entered. * The device disconnected or ended the connection. To resolve this, enter the same passkey correctly both on the printer and the device within 30 seconds. Check the status of the device, try to connect to the device again, and enter the passkey correctly.
B
Brent HillSep 5, 2025
What to do if my Sony UP-DX100 Printer displays PRINTER ERROR PLEASE RETRY?
- P
  Phillip ShawSep 5, 2025
  If your Sony Printer displays 'PRINTER ERROR PLEASE RETRY', try printing again.