What to do if my Sony VPL-DS100 says 'High temp.! Probably use in high altitude.'?
If your Sony Projector displays 'High temp.! Probably use in high altitude', and you are using it at an altitude of 1,500 m or higher, set the “High Altitude Mode” in the INSTALL SETTING menu to 'on'.
What does 'Please replace the LAMP' mean on my Sony VPL-DS100 Projector?
If your Sony Projector displays the message 'Please replace the LAMP', replace the lamp.
What does 'Please clean the filter' mean on my Sony Projector?
If your Sony Projector displays the message 'Please clean the filter', clean the filter.
How to fix incorrect color balance or a dark picture on my Sony VPL-DS100 Projector?
To correct the color balance or a dark picture on your Sony Projector, start by adjusting the picture settings. Ensure the projector is set to the correct color system to match the input. Properly adjust the contrast or brightness in the “Adjust Picture...” menu. If the issue persists, the lamp may be burnt out or dim, and you may need to replace it.
How to fix strange colors from INPUT A connector on my Sony VPL-DS100 Projector?
If the picture from the INPUT A connector on your Sony Projector appears to have strange colors, the “Input-A Signal Sel.” setting in the SET SETTING menu is incorrect. Select “Computer,” “Video GBR” or “Component” correctly according to the input signal.
What to do if the image extends beyond the screen on my Sony Projector?
If the image extends beyond the screen on your Sony Projector, and there are black edges around the image, display the full image on the screen and press the APA key. You can also adjust “Shift” in the INPUT SETTING menu.
Why won't the powered tilt adjuster and lens protector close on my Sony VPL-DS100?
If the powered tilt adjuster and the lens protector won't close on your Sony Projector, and the AC power cord was unplugged while the projector was on, reconnect the power cord to the AC outlet and then turn off the projector.
What does it mean when my Sony VPL-DS100 Projector says 'Please check Input-A Signal Sel.'?
The message 'Please check Input-A Signal Sel.' on your Sony Projector indicates that the “Input-A Signal Sel.” setting in the SET SETTING menu is not correctly configured. If you are inputting RGB signal from the computer when “Input-A Signal Sel.” in the SET SETTING menu is set to “Component,” set “Input-A Signal Sel.” correctly.
Why is the picture not clear on my Sony VPL-DS100?
If the picture on your Sony Projector is not clear, first adjust the focus. If that doesn't work, condensation may have occurred on the lens. Leave the projector on for about two hours to resolve this.
What does it mean when the LAMP/COVER indicator lights up on my Sony VPL-DS100?
When the LAMP/COVER indicator lights up on your Sony Projector, it could mean that the lamp has reached the end of its life and needs to be replaced. Alternatively, the lamp may be overheating. In this case, wait for 90 seconds to allow the lamp to cool down before turning the power back on.
Optical| projection system | 3 LCD panels, 1 lens projection system |
|---|---|
| panel | 0.62-inch TFT LCD 1, 440, 000 pixels (480, 000 pixels x 3) |
| projection lens | 1.2 times F2.2 to 2.4 f18.0 to 21.6mm |
| light output | 1200ANSI lm (lamp mode high) |
Screen Coverage| screen coverage | 40'' to 150'' (measured diagonally) |
|---|---|
| throwing distance 40-inch | 1.1 to 1.4 m (3.6 to 4.6 feet) |
| throwing distance 60-inch | 1.7 to 2.1 m (5.6 to 6.9 feet) |
| throwing distance 80-inch | 2.3 to 2.8 m (7.5 to 9.2 feet) |
| throwing distance 100-inch | 2.9 to 3.5 m (9.5 to 11.5 feet) |
| throwing distance 120-inch | 3.5 to 4.2 m (11.5 to 13.8 feet) |
| throwing distance 150-inch | 4.4 to 5.3 m (14.4 to 17.4 feet) |
Power| power requirements | AC 100 to 240 V, 50/60 Hz |
|---|---|
| power consumption max | 250 W |
| standby power consumption | 4.6 W |
Operating Environment| operating temperature | 0 to 35 degrees Celsius (32 to 95 F) |
|---|---|
| operating humidity | 35% to 85% (no condensation) |
| heat dissipation | 853.1BTU |
Input and Connectivity| input RGB/Component | Analog RGB (HD D-sub 15 pin x 1) |
|---|---|
| input S-Video | S-Video (Mini DIN 4pin x 1) |
| input composite | Composite video (RCA pin x 1) |
Weight and Dimensions| dimension (WxHxD) inch | 11 [5]/8 x 3 [1]/8 x 9 [3]/8 |
|---|---|
| dimension (WxHxD) mm | 295 x 78 x 238 |
| weight lb | Approx. 6 lbs., 3 oz. |
| weight kg | Approx. 2.8 kg |
To Next Page
