Need help?Do you have a question about the Sony VPL-EX120 and is the answer not in the manual?
Displays the projector and remote commander appearance.
Identifies the locations of main circuit boards within the projector.
Provides step-by-step instructions for disassembling various projector components.
Lists and describes optional extension boards and cables for the projector.
Explains how to access and use the network service mode for updates and traces.
Details the meaning of indicator light blinking patterns for error status.
Provides guidance on using lead-free solder for board repairs.
Offers specific procedures for adjustments after replacing key components like prism block or main board.
Describes mechanical adjustments, specifically polarizer alignment for image quality.
Details electrical adjustments including required equipment and procedures like V COM and angle sensor calibration.
Outlines the preparation and procedures for updating projector firmware via network or serial connection.
Explains procedures for saving and writing various data types like 3Dgamma, DDC, and NVM.
Lists initial data values for various picture and function adjustments.
Provides a flowchart for diagnosing and resolving projector issues based on symptoms.
Describes the function of major circuit blocks like the main board, sensor board, and G board.
Contains important notes regarding safety, standardization, stock, and harnesses for repair parts.
Shows exploded diagrams of projector components with part numbers for VPL-EX100/EX120.
Lists the packing materials and accessories supplied with the projector.
Presents the overall block diagram of the projector's main systems and connections.
Illustrates the internal wiring connections between different boards and components.
Displays the projector and remote commander appearance.
Identifies the locations of main circuit boards within the projector.
Provides step-by-step instructions for disassembling various projector components.
Lists and describes optional extension boards and cables for the projector.
Explains how to access and use the network service mode for updates and traces.
Details the meaning of indicator light blinking patterns for error status.
Provides guidance on using lead-free solder for board repairs.
Offers specific procedures for adjustments after replacing key components like prism block or main board.
Describes mechanical adjustments, specifically polarizer alignment for image quality.
Details electrical adjustments including required equipment and procedures like V COM and angle sensor calibration.
Outlines the preparation and procedures for updating projector firmware via network or serial connection.
Explains procedures for saving and writing various data types like 3Dgamma, DDC, and NVM.
Lists initial data values for various picture and function adjustments.
Provides a flowchart for diagnosing and resolving projector issues based on symptoms.
Describes the function of major circuit blocks like the main board, sensor board, and G board.
Contains important notes regarding safety, standardization, stock, and harnesses for repair parts.
Shows exploded diagrams of projector components with part numbers for VPL-EX100/EX120.
Lists the packing materials and accessories supplied with the projector.
Presents the overall block diagram of the projector's main systems and connections.
Illustrates the internal wiring connections between different boards and components.
General| Matrix size | 0.63 \ |
|---|---|
| Heat dissipation | 1023 BTU/h |
| Projection distance | - m |
| Vertical scan range | 47 - 93 Hz |
| Horizontal scan range | 14 - 93 kHz |
| Projection technology | LCD |
| Contrast ratio (typical) | 2500:1 |
| Screen size compatibility | 30 - 300 \ |
| Projector native resolution | XGA (1024x768) |
| Keystone correction, vertical | ±30 ° |
| Resolution | 1600 x 1200 pixels |
| Aspect ratio | 4:3 |
| RS-232 ports | 1 |
| Dimensions (WxDxH) | 313.4 x 278.3 x 129.6 mm |
| Lamp type | UHP |
| Lamp power | 210 W |
| Light source type | Lamp |
| Service life of light source | 4500 h |
| Service life of light source (economic mode) | 6000 h |
| Focus | Manual |
| Focal length range | - mm |
| 3D | - |
| Full HD | No |
| HD-Ready | Yes |
| Analog signal format system | NTSC, PAL, SECAM |
| RMS rated power | 1 W |
| Serial interface type | RS-232 |
| USB 2.0 ports quantity | 0 |
| Power consumption (standby) | 8 W |
| Power consumption (typical) | 300 W |
| Noise level | - dB |
| Storage temperature (T-T) | -20 - 60 °C |
| Operating temperature (T-T) | 0 - 40 °C |
| Product color | Black, White |
| Market positioning | Portable |
Weight and Dimensions| Weight | 3200 g |
|---|
To Next Page
