Sony XKS-C9111 - Setting an Output Format Converter

463
In the Engineering Setup >Switcher >Output >Internal FC
menu (7333.15), press [FC Adjust] to open the FC Adjust
menu (7333.6).
The operation is the similar to setting format converter
inputs.
For details, see “Setting the format converter conversion
method” (page 448).
Setting an Output Format Converter
You can set an output format converter for outputs of the
following output connector boards.
• XKS-S9167 12G-SDI Output Board
• XKS-C9121 100G IP Input and Output Board
• On the XVS-8000/7000/6000, output format converters
are not available.
• The XKS-C9121 has the following restrictions.
- This setting is available only when the switcher signal
format is 3840×2160P 2SI or 1080P.
- When the switcher signal format is 3840×2160P 2SI,
an output format converter can be configured on only
the 1st & 2nd and 9th & 10th outputs of each board.
- When the switcher signal format is 1080P, an output
format converter can be configured on only the 1st to
4th and 9th to 12th outputs of each board.
• When an XKS-C9121N NMI Input and Output Board is
installed, an output format converter can be configured,
but conversion formats other than “3840×2160P (Level
A, 2SI)” are not supported.
Setting the conversion format
You can set the signal format of outputs to convert by the
format converter.
The conversion format is set in the following groupings,
depending on the switcher signal format.
• XKS-S9167
- 3840×2160P 2SI or 3840×2160P SQD, and the
conversion format is 3840×2160P 2SI 12G, 1080P,
1080i: Groups of 2 outputs
1)
- 3840×2160P 2SI or 3840×2160P SQD, and the
conversion format is 3840×2160P 2SI 3G,
3840×2160P SQD: Groups of 4 outputs
- 1080P, 1080i, 720P: Groups of 4 outputs
• XKS-C9121
- 3840×2160P 2SI: Groups of 2 outputs (1st and 2nd,
9th and 10th outputs only)
- 1080P: Groups of 4 outputs (1st to 4th, 9th to 12th
outputs only)
1) Groups of 4 outputs when the conversion format is initially set to
3840×2160P 2SI 3G or 3840×2160P SQD and then the conversion format
is changed
• When the switcher signal format is 3840×2160PsF or
1080PsF, output signal format conversion is not
available.
• When the switcher signal format is 3840×2160P SQD,
the output format converter is disabled for output
connectors to which multi viewer outputs are assigned.
Supported formats
The supported conversion formats are given below.
Field frequency and frame frequency conversion is not
supported.
Item Conversion format
Enhancer • 3840×2160P (Level A, 2SI) t
1080P (Level A)
• 3840×2160P (Level A, 2SI) t
1080P (Level B)
• 3840×2160P (Level A, 2SI) t 1080i
Up-converter
aspect ratio
–
Down-converter
aspect ratio
• 1080i t 576i
• 1080i t 480i
•720P t 576i
•720P t 480i
I/P converter
conversion mode
• 1080i t 720P
Up-converter
conversion mode
–
Notes
Notes
Note
Switcher signal
format
Output signal format
3840×2160P
(Level A, 2SI)
• 3840×2160P (Level A, 2SI) 3G
a) b)
• 3840×2160P (Level A, 2SI) 12G
a) c)
• 3840×2160P (Level B, 2SI) 3G
b)
• 3840×2160P (Level A, SQD)
b)
• 3840×2160P (Level B, SQD)
b)
• 1080P (Level A)
• 1080P (Level B)
b)
• 1080i
3840×2160P
(Level A, SQD)
• 3840×2160P (Level A, 2SI) 3G
• 3840×2160P (Level A, 2SI) 12G
• 3840×2160P (Level B, 2SI) 3G
• 3840×2160P (Level A, SQD)
a)
• 3840×2160P (Level B, SQD)
1080P
(Level A)
• 1080P (Level A)
a)
• 1080P (Level B)
b)
• 1080i
• 720P
b)
1080i • 1080i
a)
• 720P
b)