What to do if Sotera Measuring Instruments meter is not consistent?
If your Sotera Measuring Instruments meter is not consistent, it might be due to air in the system, particulates in the fluid, or a worn or damaged meter chamber. Prime the system and fix any suction leaks at the pump. You can also put a screen in front of the meter. Consider cleaning or replacing the chamber.
Why is the display flashing on my Sotera Measuring Instruments?
A flashing or dim display on your Sotera Measuring Instruments meter usually indicates low batteries. Replace the batteries to resolve this issue.
What to do if fluid flows but Sotera 825P Measuring Instruments meter won't count?
If fluid is flowing, but your Sotera Measuring Instruments meter isn't counting, the meter disk might be sticking, or the driver or magnet could be damaged, or the meter might have failed. Try cleaning out the meter chamber. If that doesn't work, repair or replace the chamber assembly, or repair or replace the meter.
How to stop Sotera Measuring Instruments from leaking at the port?
If you notice fluid leaking at the inlet or outlet port of your Sotera Measuring Instruments, it could be due to the need for thread sealant or a cross-threaded port. Try adding Teflon pipe tape to the joint. If the leak persists, replace the body.
Why does my Sotera 825P Measuring Instruments meter read high?
If your Sotera Measuring Instruments meter reads high, there may be air in the system or the calibration factor is wrong. Prime the system and fix any suction leaks at the pump. Alternatively, use a higher calibration factor.
Why is my Sotera 825P Measuring Instruments meter inconsistent?
Inconsistent readings on your Sotera Measuring Instruments meter can be caused by air in the system, particulates in the fluid, or a worn or damaged meter chamber. Prime the system and fix any suction leaks at the pump. Install a screen in front of the meter. Clean the chamber. Replace the chamber.
What does Err1 mean on Sotera Measuring Instruments meter?
If you see 'Err1' on your Sotera Measuring Instruments meter, it could be due to damaged electronics or a software fault. Try repairing or replacing the electronics. Alternatively, press '2' and then recalibrate the meter.
What does Err0 mean on Sotera Measuring Instruments meter?
If you see 'Err0' on your Sotera Measuring Instruments meter, it could be due to a calibration error or a damaged chamber. Recalibrate the meter with a more accurate container. If that doesn’t work, replace the chamber.
What does Err2 mean on Sotera Measuring Instruments?
If your Sotera Measuring Instruments displays 'Err2', it means there is a bad eeprom. Replace the electronics to fix this problem.
What does Err1 mean on Sotera Measuring Instruments?
If your Sotera Measuring Instruments displays 'Err1', it could be due to damaged electronics or a software fault. Try repairing or replacing the electronics. Alternatively, press 2 and then recalibrate the meter.
General| Brand | Sotera |
|---|---|
| Model | 825P |
| Category | Measuring Instruments |
| Language | English |
Explains danger, warning, and caution symbols and their meanings.
Describes the 825P/850P meters as nutating disk positive displacement meters using magnetic coupling.
Tips to prevent cross-threading when installing the meter into threaded joints.
Step-by-step guide to reposition the meter's electronics module for optimal viewing.
Steps to adjust the calibration factor by pressing specific buttons.
Detailed steps for setting the CAL factor, priming, and adjusting the meter's reading.
Instructions for safely replacing the meter's batteries, including cautions.
Procedure for cleaning a meter that is plugged due to hardened chemical or debris.
How to select and set pulse output configurations for different units of measure.
How to display the current flow rate and its relation to output signals.
Instructions for changing the meter's displayed unit of measure.
Steps to set up custom units of measure based on ounces per special unit.
How to reset the accumulated total on the meter display.
Procedure to check the meter's calibration by verifying pulse counts.
How to flush the meter without adding to the totalizer using the FLSH mode.
To Next Page
