Soundcast VG3 - Page 6

Bluetooth pairing with NFC
1.
Enable Bluetooth
and
NFC
functions
on
your
mobile
device
2.
Hold
phone near the
NFC
logo [logo)
on
VG3 unit
until mobile
device connects and
Bluetooth
LED
blinks slowly
3.
Press
OKjConnect
on your
mobile
device
to
complete
pairing
4.
Play audio
Standard Bluetooth Pairing
1.
Enable Bluetooth
on
your
mobile device
2.
Pair a new device: press the VG3
Bluetooth
button
[Biuetooth
LED
will blink slowly)
3.
From Bluetooth
menu
on
mobile
device settings.
select "VG3
by
Soundcast_xxxxxx"
4.
Once
paired, the
Bluetooth
LED
becomes
solid blue
~
Press
&
Hold Bluetooth button
for
(2) seconds and
beep is heard
to
re-enter pairing mode
to
pair a new
or
additional
device.
~To
clear all devices
from
memory, press and
hold
the
Bluetooth
button
for
[ 1
0)
seconds
until
the Bluetooth
LED
double blinks
and third confirmation beep is heard.
Aux
Input
Mode
Plug external
audio source into
3.5mm
jack
to
automatically
switch
to
Aux
Input
mode as indicated
by
Aux
LED
turns
yellow.
Remove
3.5mm
plug
to
switch
back
to
Bluetooth
operation.
Qualcomm TrueWireless™
Stereo
(TWS)
Pairing
With
TWS,
two VG3 units may be paired
for
synchronous
Bluetooth playback.
Power off.
volume
and
TWS
mode
will
by
synchronized and may
be
controlled
from
either unit.
1.
Both speakers
must
be
powered
on
in
Bluetooth
mode [no Aux input connected)
2.
At
least
one of the speakers
must
be paired
to
audio
source (as described above) Press and
hold
the
TWS
((1*1))
for
[2) seconds
until
a confirmation beep is
heard. The
TWS
LED
will
start
to
blink slowly. Repeat with
the second VG3 unit
6
3.
When
paired, the
TWS
LED
on
both units
will
show
both
blue
and orange [purple)
~
When
in
TWS
mode and
you
tum
off one unit,
the
other
unit will
turn
off
automatically
4.
Reconnecting: The TW8-paired units
will
re-connect
to
each
other
automatically
after
turning
both units
on.
A
short
press of the
TWS
button
on
either unit
allows
cycling through the
TWS
modes (stereo,
left/right,
off)
as indicated below;
•
LED
blue
and orange:
left/
right
from
each speaker
•
LED
orange
only:
left
from
primary
speaker. right
from
secondary speaker
•
LED
off:
TWS
off
~To
clear all
devices
from
TWS
memory and return
to
single
device operation, press and hold
the
TWS
button
for
[ 1
D)
seconds until
third beep is heard and the TWS
LED
double blinks, then
tum
the
unit off. Wheri unit is
turned
on
again, the
TWS
LED
will
not
be
on.
indicating
that
TWS
is
disabled.
~
If
you
experience any
difficulty
with either standard
Bluetooth
pairing
or
TWS
operation. the VG3
Bluetooth
system can be
reset
by
clearing
pairing memory of both
Bluetooth
and
TWS
by
using the
[1
0)
second press and
hold
function (third beep) of each button and then power
cycling the unit.
~
No music
or
intermittent
dropouts? VG3 primary and
secondary units may
be
too
far
away
from
each other.
Handsfree Speakerphone Operation
1.
If your phone receives a
call while
paired with the VG3
press the
play/
pause button
to
answer the
call.
VG3 will
become a hands-free speaker phone
2.
When
call
is
complete,
press the
Play/Pause
button
to
end the call.
VG3
will automatically
return
to
your previous
music source
~
If
Keypad Auto-Lock
or
Child
Lock is active when
call
is
received,
the
keypad will automatically unlock
for
duration
of
call
and re-engage
after
call completes.
Qualcomm
TrueWireless™
is
a product of Qualcomm Technologies
International,
Ltd.