MCD1700 / English instruction manual
ENG 7
ENCODING OF CD/PHONO INTO MP3 FILE TO USB MEMORY
THE SYSTEM IS ABLE TO ENCODE NORMAL CD OR TURNTABLE TO MP3 FORMAT AND RECORDING AT
MEMORY MEDIA WITH USB CONNECTING PORT (OR SM/MMC CARD SLOT). BEFORE STARTING THE
ENCODING, PLEASE INSERT THE MEMORY MEDIA (USB PEN DRIVE OR SD/MMC CARD) TO THE SYSTEM &
MAKE SURE IT HAD ADEQUATE FREE MEMORY SIZE FOR RECRODING:-
A) CD ENCODING
I) ECNODING 1 TRACK / 1 DISC
1. PERFORM NORMAL PLAYBACK OF THE CD TRACK YOU WANT TO ENCODE & RECORD,
2. PRESS “ “ BUTTON (3) DURING THE PLAYBACK OF THE DESIRE TRACK AND THE SYSTEM
WILL START ENCODING.
3. THE SYSTEM WILL SHOW “ ” & “ “ AND FLASHING. ENCODING IS PERFORMING NOW.
4. PRESS THE “ “ BUTTON (8) REPEATLY AGAIN TO SELECT RECORD 1 TRACK “ REC_ONE “ OR
RECORD ONE ENTIRE DISC “ REC_ALL “.
5. AFTER COMPLETING OF RECRODING, UNIT WILL STOP PLAYBACK AUTOMATICALLY.
II) ENCODING BY PROGRAM
1. PLACE A CD WITH THE PRINTED SIDE FACING UP INSIDE THE TRAY & THEN CLOSE THE CO DOOR
2. SELECT THE DESIRE TRACKS BY FOLLOWING “ CD DISC PROGRAMMING “ PROCEDURES. THEN
PRESS “ CD PLAY/PAUSE “ BUTTON (14) TO START PLAYBACK.
3. PRESS THE “ “ BUTTON (8) AND THE UNIT WILL DISPLAY “ ” & “ “ AND FLASHING.
ENCODING IS NOW PERFORMING.
4. PRESS THE “ “ BUTTON (8) REPEATLY AGAIN TO SELECT “ REC_ALL “.
5. AFTER COMPLETING OF ENCODING ACCORDING TO THE PRESET PROGRAM, UNIT WILL STOP
PLAYBACK AUTOMATICALLY.
REMARK:-
- SAME OPERATION PROCEDURE FOR ENCODING TO SD/MMC CARD.
- IF BOTH RECRODING SOURCE (USB PEN DRIVE AND SD/MMC CARD) BEING DETECTED BY THE
SYSTEM DURING ENCODING, PLEASE PRESS “SKIP UP
OR DOWN ” BUTTON (2) TO SELECT THE
DESIRE SOURCE. THEN PRESS “
REC “ BUTTON (3) AGAIN TO CONTINUOUS THE PROCESS.
- THE RECORDING SPEED IS 1:1 AND ACCORDING TO THE ACTUAL PLYING TIME OF THE CD TRACK
- THE SYSTEM WILL CREAT A “ AUDIO “ FOLDER AND THEN STORE THE ENCODING TRACK IN IT.
THE RECORDING FORMAT IS PRESET AT – MP3
BIT RATE : 128 KBPS, SAMPLING RATE : 44.1KHZ
- NO SONG TITLE WILL BE RECORDED DURING ENCODING MODE
- TO INTERRUPT THE RECRODING, PRESS THE“
STOP
“ BUTTON (14) DURING RECORDING MODE.
- RECORDING WILL BE COMPLETED ONLY ENTIRE SONG BEING ENCODED, IF TERMINATE THE
ENCODING PROCESS INTERMEDIATELY, THERE IS NO TRACK BEING RECORDED NOR STORED TO
THE USB OR SD/MMC CARD
IV) COPYING OF MP3 FILE
IF PUTTING A MP3 DISC INSTEAD OF A CD-DISC, THE SYSTEM WILL COPY THE FILES TO THE USB OR
SD/MMC CARD IF PRESS THE “ REC “ BUTTON (3). THE OPERATION PROCEDURES IS SAME AS CD
ENCODING AS STIPULATE ON ABOVE, AND THE SYSTEM WILL SWITCH TO COPYING MODE ONLY IF MP3
FILE BEING READ.
REMARK:
- THE SYSTEM WILL STORE THE FILE TO USB SORCE FIRST IF BOTH USB AND SD SLOT ARE BEING
OCCUPLIED BY STORAGE MEDIA.
- THE SYSTEM WILL CREAT A “ FCOPY “ FOLDER AND THEN STORE ALL COPY FILE IN IT.
- IF PRESS THE“
REC “ BUTTON (3) DURING PLAYBACK OF USB OR SD SOURCE, THE FILE WILL COPY
FROM USB TO SD OR SD TO USB.
To Next Page
Loading...
