Soyal AR-881EF User Manual

SOYAL
ACCESS CONTROL SYSTEM
®
AR-881EF/AR-881EV
V110221
AR-881EFAR-881EV
or
P1
P2
P3
P6P4
P7P5
P1 P2 P3
P4 P5 P6 P7
※
1
2
3
1
2
3
4
5
Contents
1
Product
2
User Guide
3
Terminal Cables
4
Tools
Protection Plug
Security Torx Wrenches
Flat Head Hex Socket
Screw: M3x8
Flat Head Cap Philips
Tapping Screw: 4x38
Wire Application Wire Color Description
Lock Relay
1 Blue White (N.O.)DC24V1Amp
2
Purple White (N.C.)DC24V1Amp
Common-COM-Point
3 White (COM)DC24V1Amp
Door Contact 4 Orange Negative Trigger Input
Exit Switch 5 Purple Negative Trigger Input
Alarm Relay 6 Gray
Transistor Output Max. 12V/100mA
(Open Collector Active Low)
Power
7 Thick Red DC 12V
8 Thick Black DC 0V
P1Cable:
Wire Application Wire Color Description
Anti-Tamper
Switch
1 Red N.C.
2 Orange COM
3 Yellow N.O.
P5Cable:
Wire Application Wire Color Description
Power 1 Red DC 12V
Output
Security trigger signal 2 Purple Security trigger signal Output
Arming 3 Red White Arming Output
Duress 4 Yellow White Duress Output
P6Cable:
Wire Application Wire Color Description
1 --- ---
2 --- ---
TCP/IP Output
3
Orange White
Net - RX-
4 Orange
Net - RX+
5 Green White
Net - TX-
6 Gerrn
Net - TX+
7 --- ---
P3Cable:
Wire Application Wire Color Description
RS-485 for Lift
Controller
1 Thick Green RS-485(B-)
2 Thick Blue RS-485(A+)
P4Cable:
Wire Application Wire Color Description
Beeper 1 Pink Beeper Output
5V/100mA, Low
LED
2 Yellow Red LED Output
5V/20mA, Max
3 Brown Green LED Output
5V/20mA, Max
Door Output 4 Blue White
Transistor Output Max. 12V/100mA
(Open Collector Active Low)
Wiegand
5 Thin Green Wiegand DAT: 0 Input
6 Thin Blue Wiegand DAT: 1 Input
WG Door
Contact
7 Orange Negative Trigger Input
WG Exit Switch 8 Purple Negative Trigger Input
P2Cable:
External WG keyboard
※
If you want to program system on controller directly, please order WG keyboard then install it according to the following pattern.
Remove the Protection plug that in the bottom left.
(
※
Do not lose protection plug or it will affect the protection level.)
WG Keyboard cable will be connected to the pin board.
WG Keyboard connected to the controller from the bottom left of the hole.
When you nish programming system, please put protection plug back to the
controller.
Installation
Connector Table
Wire Application Wire Color Description
Doorbell
1 Black White
Transistor Output Max. 12V/100mA
(Open Collector Active Low)
2
Black GND
P7Cable:
(
For the controller that doorbell function.
)
Pull the cables from the square hole of the mounting plate.
Use a screwdriver to screw the base onto the wall.
Connect the terminal cables to the body and attach the body to the mounting plate.
Assemble the covers with the Allen key and screws (accessories supplied).
Turn on the power and LED will light and beep will sound.
※
only provide to the controller that have doorbell function.
P7

Soyal AR-881EF Specifications

General

Brand	Soyal
Model	AR-881EF
Category	Gateway
Language	English

Summary

Installation Guide

External WG Keyboard Setup

Instructions for installing an external WG keyboard for system programming.

Wiring Diagrams

Electric Bolt Wiring

Diagram for connecting an electric bolt lock.

Magnet Lock Wiring

Diagram for connecting a magnet lock.

Electric Strike Wiring

Diagram for connecting an electric strike.

Door Contact Wiring

Diagram for connecting a door contact sensor.

Security Enhancement with AR-721RB

Diagram for strengthening security with the AR-721RB unit.

Reader Connection Wiring

Diagram for connecting an access control reader.

Tag Management Operations

System Programming

Programming Mode Entry and Exit

Procedure for entering and exiting the controller's programming mode.

Master Code Configuration

Steps for changing the master code of the access control system.

Reader Node ID Setting

Instructions for assigning or changing the node ID for an access control reader.

Anti-pass-back Feature

Explanation and configuration of the anti-pass-back feature.

Auto Open Zone Settings

Settings for the auto open zone feature for doors.

Lift Control Configuration

Single Floor Lift Access

How to configure single floor access for users via lift control.

Multi-Floor Lift Access

Setting up access for multiple floors using lift control features.

Arming System Setup

Arming Conditions and Applications

Requirements and scenarios for enabling the arming system.

Enabling Arming Status

Configuration options for enabling arming modes like Card only or Card/Passcode.

Disabling Arming Status

Settings for disabling arming modes, including card or passcode options.

Biometric Data Management

Adding Fingerprint/Finger-Vein Data

Steps for enrolling fingerprint or finger-vein data for users.

Deleting Fingerprint/Finger-Vein Data

Process for removing enrolled fingerprint or finger-vein data.

Deleting All Biometric Data

Command to remove all enrolled fingerprint and finger-vein data.

Factory Settings Restoration

Full Device and User Data Reset

How to reset all device parameters and user card data to factory defaults.

User Card Data Reset

Specific procedure to reset only the user card data.

Firmware Upgrade Procedure

Executing Firmware Update

Step-by-step guide for upgrading the device firmware using the UdpUpdater software.

Front Panel Overview

Indicator Light Functions

Explanation of the indicator lights on the front panel and their meanings.

Finger Vein Authentication Placement

IP Address Configuration

Accessing IP Settings via Web Browser

How to access the device's IP settings using a web browser.

Online Status Monitoring

Using 'Current State' to monitor online computer connections.

User Login Credential Change

How to change the user login password for IP settings.

Network Settings Revision

Procedure for changing the device's IP address and network settings.

Securing IP Settings with User Password

How to change the login password to secure IP settings.

WG Keyboard Command List

Programming Mode Commands

Commands for entering, exiting, and enabling programming modes.

Node ID and IP Address Commands

Commands for setting Node ID and IP address for the device.

Time Delay and Relay Commands

Commands for configuring door relay, alarm relay, and delay times.

Master Card and Code Management Commands

Commands for master card setup and master code changes.

Auto-open Zone and Arming Commands

Commands for auto-open zones and arming configurations.

Tag and User Mode Commands

Commands for suspending/deleting tags and setting card/PIN modes.

Duress, PWD, and Arming Commands

Commands related to duress codes and arming passwords.

Door Open Waiting and Induction Commands

Commands for door open waiting time and card induction.

Lift Control and Factory Reset Commands

Commands for lift control, relay time, and factory reset.

WG Keyboard Command List (Continued)

Anti-pass-back and Lift Control Commands

Commands for anti-pass-back and single door lift control.

Duress, Tag Deletion, Interval Commands

Commands for duress functions, tag deletion, and tag reading intervals.

Alarm Ring and Holiday Schedule Commands

Commands for auto-ring alarm schedules and holiday settings.

Access Status and RS485 Port Commands

Commands for enabling/disabling access status and configuring RS485 port.

Biometric Form Configuration Commands

Commands for configuring biometric forms like fingerprint and finger-vein.

Function Default Value Commands

Overview of default values for functions like Auto Re-lock, Auto Open, Anti-pass-back.