Speed Queen AWNA62 User Manual (English)

Other manuals for Speed Queen AWNA62

Questions and Answers:

C
christineayalaAug 15, 2025
What to do if my Speed Queen Washer won’t fill?
- A
  Amber MatthewsAug 16, 2025
  If your Speed Queen washer isn't filling, try these solutions: First, ensure the lid is completely closed and the power cord is fully plugged into the electrical outlet. If the OPTIONS switch is set to HIGH EFFICIENCY, remember the rinse cycle uses a spray instead of filling the tub. Check that both hot and cold water faucets are turned on and the fill hoses aren't kinked. Press and hold the start button for two seconds. Ensure the controls are properly set and the last spin cycle has completed. Check the house fuse or circuit breaker. Clean the screens in the water mixing valve and the filter screens at the faucet end of the fill hoses. Also, ensure the drain hose is properly installed, referring to the Installation Instructions, to prevent water from siphoning during the cycle.
H
Hannah ClarkAug 19, 2025
Why does my Speed Queen AWNA62 Washer stop or pause during the cycle?
- N
  Nicole CraneAug 19, 2025
  Pauses during a cycle are a normal part of the Speed Queen washer's operation. Ensure the lid is closed for the cycle to advance. Check the house fuse or circuit breaker. The motor overload protector may have stopped the cycle; it will reset in two to three minutes and restart the washer automatically.
P
Peter SanchezAug 21, 2025
What to do if my Speed Queen Washer won’t start?
- M
  mistyhodgeAug 21, 2025
  If your Speed Queen washer isn't starting, make sure the lid is closed and press and hold the start button for two seconds. Ensure the power cord is fully plugged into the electrical outlet and that the controls are properly set. Check the house fuse or circuit breaker. Also, the motor overload protector may have stopped the cycle; it will reset itself in two or three minutes and restart the washer automatically.
K
Kimberly BurchAug 25, 2025
Why is my Speed Queen AWNA62 so noisy?
- D
  Damon ButlerAug 26, 2025
  If your Speed Queen washer is making excessive noise, the wash load may be unbalanced; open the lid and redistribute the load. Also, ensure the washer is level, as uneven leveling can cause vibration. A newly installed washer may make a knocking sound if the machine has been in storage; run the washer through 4-5 cycles to loosen the belt. Washer operation will not be affected.
N
nfordAug 28, 2025
What to do if my Speed Queen AWNA62 won’t drain?
- C
  cheyenne43Aug 28, 2025
  If your Speed Queen washer isn't draining, first check that the drain hose isn't kinked, twisted, or clogged. Also, make sure the drain receptacle isn't clogged. Refer to the Installation Instructions to make sure that the drain hose has been properly installed.
H
Hector DunnAug 30, 2025
Why is my Speed Queen AWNA62 not spinning?
- M
  Michael CraneAug 31, 2025
  If your Speed Queen washer isn't spinning, make sure the lid is closed and press and hold the start button for two seconds. Also, ensure the power cord is fully plugged into the electrical outlet and check the house fuse or circuit breaker. The motor overload protector may have stopped the cycle; it will reset itself in two or three minutes and restart the washer automatically. If the drive belt is broken, call a service person.
D
Dawn AndersonSep 3, 2025
How to fix water leaks in Speed Queen AWNA62?
- O
  ochurchSep 3, 2025
  To address water leaks in your Speed Queen washer, check that the fill hoses are properly installed on both the faucets and the washer's water mixing valve. Consider replacing the fill hoses every five years. Ensure the drain receptacle is not clogged and check your house plumbing. If the laundry load is oversudsing or overloaded, use low-sudsing, high-efficiency (HE) detergent and ensure proper load sizes.
M
Monica MartinezSep 5, 2025
What to do if my Speed Queen AWNA62 load is too wet?
- S
  Sara SuttonSep 5, 2025
  If your Speed Queen washer leaves the load too wet, the wash load may be unbalanced; open the lid and redistribute the load. If the load is too small, add items to make a full load.
J
Jonathan AdamsSep 9, 2025
Why is my Speed Queen Washer not agitating?
- A
  April ChangSep 9, 2025
  If your Speed Queen washer isn't agitating, ensure the lid is closed and press and hold the start button for two seconds. Keep in mind that pauses are a normal part of the washer’s operation. The wash portion of the cycle will alternate between agitation and pausing. Ensure the power cord is fully plugged in and check the house fuse or circuit breaker. The motor overload protector may have stopped the cycle; it will reset itself in two or three minutes and restart the washer automatically. If the drive belt is broken, call a service person.