Why is my Speed Queen Washer so noisy?
If your Speed Queen washer is noisy, try opening the lid and redistributing the load to balance it. Make sure the washer is level. A newly installed washer may make knocking sounds if it has been in storage; running it through 4-5 cycles can help loosen the belt. Note that washer operation will not be affected.
Why does my Speed Queen AWNE92 Washer keep stopping during cycle?
If your Speed Queen washer stops or pauses during a cycle, note that pauses are a normal part of the washer's operation; the washer will stop (pause) shortly before the wash and rinse spins. Additionally, check the laundry room fuse or circuit breaker. If the motor overload protector has stopped the cycle, it will reset itself, and the display will show tp, St. Press the Start/Pause button to resume the cycle.
Why is my Speed Queen AWNE92 leaking water?
If your Speed Queen washer is leaking water, check that the fill hoses are properly installed on the faucets and the washer’s water mixing valve. Inspect the condition of the fill hoses and replace them every five years. Make sure the drain receptacle isn't clogged. Check the laundry room plumbing and the house water pressure. Leaking may occur with extremely low water pressure, or the laundry load may be oversudsing or overloaded. Use less detergent (or low-sudsing detergent) and ensure proper load sizes.
Why Speed Queen AWNE92 won't spin?
If your Speed Queen Washer won't spin, make sure the lid is closed properly. Press the Start/Pause button to start the washer, and ensure the power cord is fully plugged into the electrical outlet. Check the laundry room fuse or circuit breaker. If the motor overload protector has stopped the cycle, it will reset itself, and the display will show tp, St. Press the Start/Pause button to resume the cycle. A broken drive belt could also be the cause. Call the service person.
How to fix Speed Queen AWNE92 won't fill?
If your Speed Queen Washer won't fill, ensure the power cord is fully plugged into the electrical outlet. Check that both hot and cold water faucets are turned on, and the lid is properly closed. Make sure the fill hoses aren't kinked or twisted. Press the Start/Pause button to initiate the washer and verify that the controls are correctly set. In the Normal Eco cycle, the tub won’t fill with water during the rinse portion; instead, it uses a spray rinse. Confirm that the last spin cycle has been completed. Inspect the laundry room fuse or circuit breaker. Clean the screens in the water mixing valve and the filter screens at the faucet end of the fill hoses. If water is being siphoned, refer to the installation instructions to ensure the drain hose is correctly installed.
What to do if my Speed Queen Washer won't drain?
If your Speed Queen washer won't drain, check that the drain hose isn't kinked, twisted, or clogged. Also, ensure the drain receptacle isn't clogged. Refer to the Installation instructions to make sure that the drain hose has been properly installed.
Why is my Speed Queen AWNE92 not agitating?
If your Speed Queen Washer won't agitate, make sure the lid is closed. Press the Start/Pause button to start the washer and ensure the power cord is fully plugged into the electrical outlet. Check the laundry room fuse or circuit breaker. If the motor overload protector has stopped the cycle, it will reset itself and the display will show tp, St. Press the Start/Pause button to resume the cycle. A broken drive belt could also be the cause. Call the service person.
Why is my Speed Queen Washer load too wet?
If the load from your Speed Queen washer is too wet, it may be due to an unbalanced wash load; open the lid and redistribute the load. The load might also be too small; add items to make a full load.
Why Speed Queen AWNE92 Washer water temperature is wrong?
If the water temperature is wrong in your Speed Queen washer, ensure that the controls are properly set. Check the fill hoses and make sure the hot faucet hose is connected to the hot mixing valve (indicated with “H” on the valve bracket) and the cold faucet is connected to the cold mixing valve (indicated with “C” on the valve bracket). Also, ensure your laundry room water heater is adjusted properly. Keep in mind that the Normal Eco cycle uses a colder water temperature.
What does Er, FL mean on my Speed Queen AWNE92 Washer?
If your Speed Queen washer's digital display shows Er, FL, it means the washer hasn't reached the fill level after 30 minutes during a wash or rinse fill. Make sure both hot and cold water faucets are turned on, and that the fill hoses are not kinked or twisted. Clean the screens in the water mixing valve and the filter screens located at the faucet end of the fill hoses. Unplug the machine for 15 seconds to clear this code.
Explains the meaning of DANGER, WARNING, CAUTION, IMPORTANT, and NOTE statements found in the manual.
Lists fundamental precautions to reduce the risk of fire, electric shock, injury, or death during washer use.
Details steps like emptying pockets, mending, sorting, and pretreating clothes before washing.
Guides on how to load the washer, understand load sizes, and select appropriate water levels for effective washing.
Explains the use of Hot, Warm, Cool, and Cold water temperatures for different fabric types and washing needs.
Describes the digital display, soak indicator behavior, and status lights for cycle progression.
Introduces various wash cycles like Heavy Duty, Whites, Normal Eco, Perm Press, Delicate, and Favorite.
Describes Selections (Temp, Load Size, Soil Level) and Options (Soak, Pre-Wash, Rinses, Delay Start, Signal, Control Lock).
Step-by-step instructions for preparing and starting a wash load, including safety warnings.
Explains how to pause a running cycle and perform a manual soak operation.
Provides detailed stage breakdown, time, speed, and comments for Normal Eco and Delicate wash cycles.
Outlines stages, time, speed, and comments for Heavy Duty, Whites, Perm Press, Quick Wash, and Bulky cycles.
Explains the use and cleaning of bleach and fabric softener dispensers, along with usage tips.
Offers solutions for common problems like dinginess, yellowing, tearing, lint, and wrinkles based on their causes.
Covers cold weather care, general cleaning, hose inspection, filter screens, and vacation preparation.
Details a schedule for monthly, semi-annual, and annual maintenance tasks to ensure proper operation.
Instructions for reinstalling shipping brace and plug when moving the washer.
Explains the function of the motor overload protector and how to respond to related error codes.
Provides causes and solutions for common washer problems like not filling, starting, or agitating.
Offers solutions for problems like not spinning, draining, water leaks, noise, and wet loads.
Guides users on resolving incorrect water temperatures and interpreting various digital display error codes.
General| Brand | Speed Queen |
|---|---|
| Model | AWNE92 |
| Category | Washer |
| Language | English |
To Next Page