Speed Queen TR7000WN - User Manual

Questions and Answers

H
Heather MartinezNov 21, 2025
Why is my Speed Queen Washer not filling with water?
- S
  Shawn ButlerNov 21, 2025
  Several factors could be preventing your Speed Queen Washer from filling: * Ensure the power cord is fully plugged into the electrical outlet. * Confirm both hot and cold water faucets are completely open. * Verify the lid is securely closed. * Check that the fill hoses aren't kinked or twisted, obstructing water flow. * Press the Start/Pause button to initiate the wash cycle. * Be sure the controls are correctly set for your desired wash. * If using the Normal Eco cycle, remember the rinse portion uses a spray rinse instead of a full tub fill. * Ensure the last spin cycle has finished. * Check the laundry room's fuse or circuit breaker. * Clean the screens in the water mixing valve and the filter screens at the faucet end of the fill hoses. * Confirm the drain hose ...
C
clynchAug 25, 2025
Why is my Speed Queen TR7000WN so noisy?
- P
  pateljasonAug 26, 2025
  If your Speed Queen Washer is making excessive noise, here are a few things to check: * The wash load may be unbalanced. Open the lid and redistribute the items in the drum. * Ensure the washer is level, as uneven leveling can cause vibration. * If the washer is newly installed, a knocking sound might occur due to the belt settling after storage. Run the washer through 4-5 cycles to loosen the belt; this won't affect its operation.
P
Patrick HunterAug 26, 2025
Why is my Speed Queen TR7000WN not draining?
- M
  Michelle GibbsAug 27, 2025
  If your Speed Queen Washer isn't draining, check the following: * Ensure the drain hose isn't kinked or twisted. * Make sure the drain hose is not clogged. * Ensure the drain receptacle isn't clogged. Also, refer to the Installation instructions to verify that the drain hose has been properly installed.
R
Robin CollinsAug 27, 2025
Why is my Speed Queen Washer not spinning?
- A
  Allison JonesAug 27, 2025
  If your Speed Queen Washer isn't spinning, make sure that: * The lid is closed. * You have pressed the Start/Pause button. * The power cord is plugged into the outlet. * The laundry room fuse or circuit breaker is working. If the drive belt is broken, call a service person.
K
Kimberly LunaAug 29, 2025
How to fix water leaks in my Speed Queen Washer?
- U
  uperryAug 29, 2025
  If your Speed Queen Washer is leaking, consider these possible solutions: * Ensure fill hoses are correctly attached to both the faucets and the washer's water mixing valve. * Inspect the condition of the fill hoses for wear or damage. * Replace fill hoses every five years to prevent leaks. * Make sure the drain receptacle isn't clogged. * Check the laundry room plumbing for any issues. * Assess house water pressure, as extremely low pressure can sometimes cause leaks. * If you notice excessive suds, it might be due to oversudsing or overloading; use less detergent (or a low-sudsing detergent) and ensure proper load sizes.
P
Patrick HowardSep 16, 2025
Why is my Speed Queen TR7000WN not agitating?
- L
  Lori GonzalezSep 16, 2025
  If your Speed Queen Washer isn't agitating, make sure of the following: * The lid is completely closed. * The Start/Pause button is pressed to start the washer. * The power cord is properly plugged into the electrical outlet. * The laundry room fuse or circuit breaker is working. If the drive belt is broken, call a service person.
I
ihammondSep 14, 2025
What to do if my Speed Queen Washer load is too wet?
- R
  Rebecca GreenSep 14, 2025
  If your laundry load is coming out too wet from your Speed Queen Washer: * The wash load may be unbalanced. Open the lid and redistribute the load to balance it. * The load might be too small. Add more items to create a full load.
A
alexfoxSep 15, 2025
Why does my Speed Queen TR7000WN have too many soap suds?
- J
  Jennifer MontgomerySep 15, 2025
  If you see too many soap suds in your Speed Queen Washer: * Make sure you are using a low-sudsing, high efficiency (HE) detergent. * Ensure you're using the amount of detergent recommended on the detergent label. If you're using non-HE detergent, use only half the manufacturer's recommended amount. * Ensure you are using proper load sizes, as overloading can cause oversudsing.
D
David WongSep 6, 2025
Why is my Speed Queen Washer displaying Er, OF?
- K
  keith79Sep 6, 2025
  The 'Er, OF' code on your Speed Queen Washer indicates the washer has filled to the overflow level. If the lid is closed and locked, the machine will begin to pump water out. If the code doesn't clear, unplug the machine and call for service.
S
Steven KellySep 4, 2025
Why is my Speed Queen TR7000WN displaying Er, FL?
- J
  Jenny JonesSep 4, 2025
  The 'Er, FL' code appears if the Speed Queen Washer hasn't reached the fill level after 30 minutes during a wash or rinse fill. Make sure the hot and cold water faucets are turned on and the fill hoses are not kinked or twisted. Also, clean the screens in the water mixing valve and the filter screens located at the faucet end of the fill hoses. Unplug the machine for 15 seconds to clear this code.

Summary

General Safety Warnings

Understanding Warning Statements

Defines the meaning of DANGER, WARNING, CAUTION, IMPORTANT, and NOTE statements used in the manual.

Detailed Safety Instructions

Key Safety Precautions for Operation

Lists essential precautions for safe operation, installation, and maintenance to prevent hazards.

Washer Operation Guide

Preparing and Loading the Washer

Control Panel Overview

Washing Clothes: Step-by-Step

Washing Procedure and Pausing

Outlines the step-by-step process for washing clothes, including starting, pausing, and lid lock behavior.

Cycle Operation Details

Cycle Stage Breakdowns

Washer Maintenance Guide

Troubleshooting Common Issues

Operational Problems and Solutions

Provides solutions for common issues like no fill, no start, agitation/spin problems, leaks, noise, and control malfunctions.

Understanding Error Codes

Service and Support

Warranty Repairs and Contact