To Next PageTo Next PageWhy is my SPT WA-1140DE running but not cooling?
If your SPT Air Conditioner is running but not cooling, consider these possibilities: * Ensure all doors and windows are closed. * Check for other appliances generating heat in the room, such as heaters, lamps, or computers. * Clean the air filter if it's dirty. * Make sure the air outlet or inlet isn't blocked. * Verify that the set temperature is lower than the ambient temperature.
How to prevent water leaks when moving my SPT WA-1140DE?
To avoid water leaks when moving your SPT Air Conditioner: * Remember that the inner water reservoir is open-top. Move the unit carefully, applying gentle and even pressure on the side. * If possible, drain the water from the unit before moving it.
What to do if my SPT WA-1140DE Air Conditioner unit does not run?
If your SPT Air Conditioner doesn't start, here are a few things to check: * Make sure the plug is securely plugged in. * Check if the protector trip or fuse is blown. * Try waiting 3-5 minutes before restarting, as a delay-protection feature might be active. * Also, verify if the batteries in the remote controller need replacement.
Why does my SPT WA-1140DE Air Conditioner compressor run for a short time and then stop?
If the compressor in your SPT Air Conditioner starts and stops quickly, consider the following: * Ensure the set temperature isn't too close to the ambient temperature; lower the set temperature if needed. * Check for obstructions blocking the air outlet and remove them. * Inspect the air filters for dirt and clean them if necessary. * Verify that the outdoor temperature isn't excessively high.
What to do if my SPT WA-1140DE Air Conditioner unit does not run and the red light is flashing?
If your SPT Air Conditioner won't run and a red light is flashing, the water reservoir is likely full. Remove the rubber plug and drain the water.
General| Cooling Capacity | 11, 000 BTU |
|---|---|
| Voltage | 115V |
| Air Flow | 220 CFM |
| Refrigerant | R-410A |
| Type | Window Air Conditioner |
| Power Supply | 60Hz |
| Operating Temperature | 62°F - 90°F |
Details critical electrical requirements and safety compliance for installation.
Offers advice on optimizing unit usage for maximum energy efficiency.
Explains how a single hose system draws and exhausts indoor air.
Details how a dual hose system uses both indoor and outdoor air.
Enables the unit to resume previous settings after a power interruption.
Recycles condensation water, improving efficiency by evaporating it.
Utilizes fuzzy logic for automatic operation based on ambient temperature.
Activates rapid cooling, designed for cooling-only models.
Engages the heating function for models with this feature.
Identifies the external parts and ports of the portable air conditioner.
Details all parts necessary for the proper installation of the unit.
Guides users through fitting the window slider kit for optimal hose placement.
Recommends optimal placement for efficient operation and airflow.
Step-by-step guide for connecting hoses and securing the unit.
Outlines the order of operations for a successful unit setup.
Details the purpose and operation of each button on the main control panel.
Explains the meaning of status lights like RUN and WATER FULL.
Describes the information presented on the unit's digital display screen.
Explains the role of each button on the remote for unit control.
Provides a reference for icons and symbols used on the remote and unit.
Guidance on aiming the remote and its effective operating range.
Describes how to select and utilize different operational modes.
Explains how to adjust the fan speed for optimal comfort.
Details how to set and adjust the desired room temperature.
Steps to activate the unit after configuring settings.
How to set temperature, fan speed, and achieve desired cooling.
Explains automatic fan speed adjustment based on ambient temperature.
How to set up and operate the unit in dehumidifying mode.
Information on compressor protection during mode changes.
How the unit automatically selects modes and target temperatures.
Allows minor manual adjustments to temperature and airflow.
How to program the unit to start at a specific time.
How to program the unit to stop at a specific time.
Procedure for setting the current time on the unit.
How to activate and use the fast cooling function.
How to activate and use the heating function.
Lists scenarios that trigger protective shutdowns and required actions.
Instructions on how to empty accumulated water from the unit.
Procedure for cleaning the exterior surfaces of the air conditioner.
Instructions for maintaining the air filter for optimal performance.
Steps for safely storing the unit during off-season periods.
Addresses issues where the unit fails to power on or start.
Diagnoses and resolves compressor short-cycling problems.
Solutions for when the unit operates but does not cool effectively.
Guidance on preventing or resolving water leaks during relocation.
Troubleshooting a full water reservoir or other critical errors.
Details cooling/heating capacity, humidity removal, and airflow.
Covers power supply, amperage, and wattage requirements.
Includes room size, noise, refrigerant, and operating parameters.
Provides unit dimensions and weight for handling and placement.
Details the dimensions and weight of the product packaging.
Outlines the conditions and procedures for warranty claims.
Lists exclusions and limitations of the product warranty.
