SPX 9500 - User Manual

2-POSITION/3-POSITION, 3-WAY/4-WAY MANUAL
CONTROL VALVE
Max. Capacity: 10,000 PSI
NOTE:
●●
Inspect the valve upon arrival. The carrier, not the manufacturer, is responsible for any damage resulting
from shipment.
●●
Read and carefully follow these instructions. Most problems with new equipment are caused by improper
operation or installation.
SAFETY PRECAUTIONS
WARNING
To help prevent personal injury:
●●
Before operating the pump, all hose connections must be tightened with the proper tools. Do not
overtighten. Connections should only be tightened securely and leak-free. Overtightening can cause
premature thread failure or high pressure fittings to split at pressures lower than their rated capacities.
●●
Should a hydraulic hose ever rupture, burst, or need to be disconnected, immediately shut off the pump
and shift the control valve twice to release all pressure. Never attempt to grasp a leaking pressurized hose
with your hands. The force of escaping hydraulic fluid could cause serious injury.
●●
Do not subject the hose to potential hazard such as fire, sharp surfaces, extreme heat or cold, or heavy
impact. Do not allow the hose to kink, twist, curl or bend so tightly that the oil flow within the hose is
blocked or reduced. Periodically inspect the hose for wear, because any of these conditions can damage
the hose.
●●
Do not use the hose to move attached equipment. Stress can damage the hose, resulting in possible
personal injury.
●●
Hose material and coupler seals must be compatible with the hydraulic fluid used. Hoses also must not
come in contact with corrosive materials such as creosote-impregnated objects and some paints. Consult
the manufacturer before painting a hose. Never paint the couplers. Hose deterioration due to corrosive
materials can result in personal injury.
Form No. 102527
Sheet No. 1 of 1
Issue Date: Rev. 3-30-96
Operating & Installation
Instructions for:
9500
9501
9502
9504
9504-PARK
9505
9506
9507
9508
9508-BOC
9509
9511
9520
Note: Shaded areas reflect last revision(s) made to this form.
SPECIFICATIONS
MAX. WORKING
PRESSURE
10,000 PSI
5 GPM
500 PSI
3/8 NPTF
MAX. FLOW
RATING
MAX. VALVE
CASE (RETURN
LINE) PRESSURE
PORT SIZES
© SPX Corporation
SPX Corporation
5885 11th Street
Rockford, IL 61109-3699 USA
Tech. Services: (800) 477-8326
Fax: (800) 765-8326
Order Entry: (800) 541-1418
Fax: (800) 288-7031
SPX Corporation
655 Eisenhower Drive
Owatonna, MN 55060-0995 USA
Phone: (507) 455-7000
Tech. Services: (800) 533-6127
Fax: (800) 955-8329
Order Entry: (507) 455-1480
Fax: (800) 283-8665
International Sales: (507) 455-7223
Fax: (507) 455-7746
®
http://www.powerteam.com
Internet Address:
®

Summary

Manual Control Valve Overview

Valve Specifications

Details maximum working pressure, flow rating, and port sizes for the control valve.

Important Notes

Provides essential pre-operation checks and warnings regarding shipment damage and proper installation.

Safety Precautions

Personal Injury Prevention

Crucial advice on preventing injury, including hose connection safety, handling ruptures, and hose care.

Valve Specifications

Valve Operation Notes

Notes on valve torque, position adjustment, and use with single or double-acting cylinders.

Control Valve Set-Up Procedure

Hydraulic Connection Guidelines

Steps for connecting pump, valve, and cylinder, emphasizing thread sealant and tape usage.

Typical Work Holding Applications

Single-Acting Cylinder Circuit

Illustrates a typical work holding setup using a pump-mounted valve with single-acting cylinders.

Double-Acting Cylinder Circuit

Illustrates a typical work holding setup using a pump-mounted valve with double-acting cylinders.

SPX 9500 Specifications

General

Power Consumption	15 W
Effects	Reverb, Delay, Chorus, Flanger, Modulation
Frequency Response	20 Hz - 20 kHz
THD	<0.01%
MIDI	Yes
Input Voltage	100-240 V AC
Operating Temperature	0 - 40 °C