To Next PageTo Next PageHow to fix a Standard Horizon ECLIPSE GPS GX1400GPS/E Radio that fails to power up?
If your Standard Horizon Radio fails to power up, there are a couple of things to check: * First, ensure that the 12 VDC battery connections are secure and the fuse is in good condition. * Second, make sure the VOL knob is rotated clockwise to turn the radio on.
What to do if my Standard Horizon ECLIPSE GPS GX1400GPS/E blows a fuse when connected to the power supply?
If your Standard Horizon Radio blows a fuse when connected to the power supply, the power wires may be reversed. Check the power cable for DC voltage and replace the fuse (6 A 250 V). Ensure the red wire is connected to the positive (+) battery post and the black wire to the negative (-) battery post. If the fuse continues to blow, contact your Dealer.
Why does my Standard Horizon Radio show “HI BATTERY” or “LO BATTERY” message?
If your Standard Horizon Radio displays a “HI BATTERY” or “LO BATTERY” message when turned on, it means the power supply voltage is either too high or too low. Verify that the connected power supply voltage is between 11 and 16.6 volts DC. Also, check if the generator has malfunctioned.
How to eliminate popping or whining noise from Standard Horizon Radio speaker when engine runs?
If you're hearing popping or whining noises from the speaker of your Standard Horizon Radio while the engine is running, it's likely due to engine noise. Try rerouting the DC power cables away from the engine. You can also add a noise suppressor on the power cable, switch to resistive spark plug wires, and/or add an alternator whine filter.
What to do if my Standard Horizon ECLIPSE GPS GX1400GPS/E Radio has low transmit power?
If a receiving station reports low transmit power from your Standard Horizon Radio, even when set to HI power, the antenna may be the issue. Have the antenna checked or test the transceiver with another antenna. If the problem continues, contact your Dealer for servicing.
Why is my position not displayed on my Standard Horizon ECLIPSE GPS GX1400GPS/E Radio?
If your position is not displayed on your Standard Horizon Radio, there could be a couple of reasons: * Check the accessory cable connection. Some GPS units use the battery ground line for NMEA connection. * Verify the output signal format of the GPS navigation receiver. The radio requires NMEA0183 format with GLL, RMC, GGA, or GNS sentence as an output signal. If the GPS has a baud rate setting, ensure it is set to 4800 and parity is set to NONE.
What to do if sound is not emitted from Standard Horizon ECLIPSE GPS GX1400GPS/E speaker?
If no sound is coming from the internal or external speaker of your Standard Horizon Radio, check the connections of the accessory cable. There may be a short circuit on the External speaker cable WHITE/SHIELD.
How to fix a Standard Horizon ECLIPSE GPS GX1400GPS/E that won't turn on?
First, check the 12 VDC battery connections and the fuse. Then, make sure the VOL knob is rotated clockwise to turn the Standard Horizon Radio on.
What to do if my Standard Horizon ECLIPSE GPS GX1400GPS/E keeps blowing fuses?
Check the power cable for DC voltage and replace the fuse (6 A 250 V). Ensure the red wire is connected to the positive (+) battery post and the black wire to the negative (-) battery post. If the Standard Horizon Radio fuse still blows, contact your Dealer.
Why does my Standard Horizon ECLIPSE GPS GX1400GPS/E say 'HI BATTERY' or 'LO BATTERY'?
The power supply voltage is either too high or too low. Make sure the connected power supply voltage is between 11 volts and 16.6 volts DC. Also, check that the generator hasn't malfunctioned.
General| Power Output | 25W/1W |
|---|---|
| Channels | All USA, International and Canadian Channels |
| NMEA Output | NMEA 0183 |
| DSC Capability | Class D |
| Memory Channels | 10 |
| Type | Marine VHF Radio |
| GPS | Built-in GPS |
| Display | Dot Matrix LCD |
| Weight | 2.2 lbs |
| Waterproof Rating | IPX8 |
| Battery Life | N/A (Fixed Mount) |
