19
ENGLISH (Original Instructions)
Cable cross-sectional
area (mm
2
) Cable rated
current (Ampere)
Cable cross-sectional
area (mm
2
) Cable rated
current (Ampere)
0,75 6
1,00 10
1,50 15
2,50 20
4,00 25
Cable length (m)
7,5 15 25 30 45 60
Voltage Amperes Cable rated current (Ampere)
110-127 0 - 2,0 6 6 6 6 6 10
2,1 - 3,4 6 6 6 6 15 15
3,5 - 5,0 6 6 10 15 20 20
5,1 - 7,0 10 10 15 20 20 25
7,1 - 12,0 15 15 20 25 25 -
12,1 - 20,0 20 20 25 - - -
220-240 0 - 2,0 6 6 6 6 6 6
2,1 - 3,4 6 6 6 6 6 6
3,5 - 5,0 6 6 6 6 10 15
5,1 - 7,0 10 10 10 10 15 15
7,1 - 12,0 15 15 15 15 20 20
12,1 - 20,0 20 20 20 20 25 -
FEATURES (FIG. A)
This tool includes some or all of the following features.
1. On/Off switch
2. Lock-on button
3. Variable speed control knob
4. Plunge lock lever
5. Spindle lock button
6. Collet
7. Revolver depth stop
8. Chip deflector
9. Depth stop bar
10. Depth of cut scale
11. Dust extraction adaptor
ASSEMBLY
WARNING! To prevent accidental operation, turn off and
unplug tool before performing the following operations.
Failure to do this could result in serious personal injury.
Fitting a router bit (Fig. B)
♦ Remove the chip reflector (8).
♦ Keep the spindle lock button (5) depressed and rotate
the spindle until the spindle lock fully engages.
♦ Loosen the collet nut (12) using the spanner provided.
♦ Insert the shank of the router bit (13) into the collet (6).
Make sure that the shank protrudes at least 3mm from
the collet as shown.
♦ Keep the spindle lock button (5) depressed and tighten
the collet nut (12) using the spanner provided.
Fitting the edge guide (Fig. C)
The edge guide helps to guide the tool parallel to an edge.
♦ Fit the bars (14) to the edge guide (15) using the two
screws (16) provided.
♦ Insert the bars (14) into the router base as shown.
♦ Set the edge guide to the required distance.
♦ Tighten the fixing screws (17).
Fitting the dust extraction adaptor (Fig. D)
The Dust extraction adaptor allows you to connect a
vacuum cleaner to the tool.
♦ Connect the hose (18) of the vacuum cleaner to the
adaptor (11).
Fitting the template guide (Fig. E)
♦ Fit the template guide (19) to the base of the router, with
the flange to the bottom (workpiece) side.
♦ Insert the two long screws (20) from the bottom side
through the template guide and the holes in the base.
♦ Place a nut onto each of the screws and securely
tighten the nuts.
Fitting the distance piece (Fig. F)
(Distance piece not included)
♦ Fit the distance piece (21) to the base of the router
using the screws provided.
Fitting the centring pin (Fig. G)
♦ Fit the centring pin (22) to the workpiece side of the
bars, then tighten it with the steel knob (23) provided .
Fitting the copy follower (Fig. H)
(Copy follower not included)
♦ Fit the edge guide to the router as shown in Fig. C.
♦ Fit the bar (24) to the upper side of the edge guide using
the two screws and nuts provided.
♦ Adjust the rotating attachment (25) on the bar with the
wing knob (26).
OPERATION
WARNING! Let the tool work at its own pace. Do not overload.
♦ Carefully guide the cable in order to avoid accidentally
cutting it.
Adjusting the depth of cut (FIG. I, J and K)
♦ The depth of cut is the distance X between the depth
stop bar (9) and the depth stop (7).
♦ The depth of cut can be set in two different ways as
described below.
To Next Page
Loading...
