Stanley SST1800 - Transporting the Table Saw; Handle Assembly; SETUP AND OPERATION PROCEDURES; Riving Knife Set-up

Riving knife set-up (Fig E, F, G)
WARNING! Disconnect the mains cable! The
setup of the riving knife (3) must be checked
before each use.
1. Set the saw blade (4) to the max. cutting depth, put it at 00
position and lock it
2. Remove the table insert (20) (Fig. E)
WARNING! For transport reasons, the riving
knife (3) was fixed in the lower position before
initial commissioning. Only work with the
machine if the riving knife (3) is in the upper
position. Fitting the riving knife (3) in the upper
position is as follows:
3. Loosen the locking handle (f) and push the riving knife (3)
in the upper position (Fig.F)
To Transport The Table Saw (Fig C1, C2)
The upper legs could be locked in the vertical position for
use as a trolley handle.
WARNING! Cover the upper part of the saw blade during
transportation, for example by the guard.
Handle assembly (Fig D)
Place washer (e), housing (b), washer (c) and hex nut (d) on
the bolt (a) to assemble the handle (11)
204
E
C1
B4
2
1
C2
d
c
b
e
a
11
D
Riving knife set-up (Fig E, F, G)
WARNING! Disconnect the mains cable! The
setup of the riving knife (3) must be checked
before each use.
1. Set the saw blade (4) to the max. cutting depth, put it at
00 position and lock it
2. Remove the table insert (20) (Fig. E)
Riving knife set-up (Fig E, F, G)
WARNING! Disconnect the mains cable! The
setup of the riving knife (3) must be checked
before each use.
1. Set the saw blade (4) to the max. cutting depth, put it at 00
position and lock it
2. Remove the table insert (20) (Fig. E)
WARNING! For transport reasons, the riving
knife (3) was fixed in the lower position before
initial commissioning. Only work with the
machine if the riving knife (3) is in the upper
position. Fitting the riving knife (3) in the upper
position is as follows:
3. Loosen the locking handle (f) and push the riving knife (3)
in the upper position (Fig.F)
To Transport The Table Saw (Fig C1, C2)
The upper legs could be locked in the vertical position for
use as a trolley handle.
WARNING! Cover the upper part of the saw blade during
transportation, for example by the guard.
Handle assembly (Fig D)
Place washer (e), housing (b), washer (c) and hex nut (d) on
the bolt (a) to assemble the handle (11)
204
E
C1
B4
2
1
C2
d
c
b
e
a
11
D
WARNING! For transport reasons, the riving
knife (3) was xed in the lower position before
initial commissioning. Only work with the
machine if the riving knife (3) is in the upper
position. Fitting the riving knife (3) in the upper
position is as follows:
3. Loosen the locking handle (f) and push the riving knife (3)
in the upper position (Fig.F)
Riving knife set-up (Fig E, F, G)
WARNING! Disconnect the mains cable! The
setup of the riving knife (3) must be checked
before each use.
1. Set the saw blade (4) to the max. cutting depth, put it at 00
position and lock it
2. Remove the table insert (20) (Fig. E)
WARNING! For transport reasons, the riving
knife (3) was fixed in the lower position before
initial commissioning. Only work with the
machine if the riving knife (3) is in the upper
position. Fitting the riving knife (3) in the upper
position is as follows:
3. Loosen the locking handle (f) and push the riving knife (3)
in the upper position (Fig.F)
To Transport The Table Saw (Fig C1, C2)
The upper legs could be locked in the vertical position for
use as a trolley handle.
WARNING! Cover the upper part of the saw blade during
transportation, for example by the guard.
Handle assembly (Fig D)
Place washer (e), housing (b), washer (c) and hex nut (d) on
the bolt (a) to assemble the handle (11)
204
E
C1
B4
2
1
C2
d
c
b
e
a
11
D
To Transport The Table Saw (Fig C1, C2)
The upper legs could be locked in the vertical position for use
as a trolley handle.
WARNING! Cover the upper part of the saw blade during
transportation, for example by the guard.
Riving knife set-up (Fig E, F, G)
WARNING! Disconnect the mains cable! The
setup of the riving knife (3) must be checked
before each use.
1. Set the saw blade (4) to the max. cutting depth, put it at 00
position and lock it
2. Remove the table insert (20) (Fig. E)
WARNING! For transport reasons, the riving
knife (3) was fixed in the lower position before
initial commissioning. Only work with the
machine if the riving knife (3) is in the upper
position. Fitting the riving knife (3) in the upper
position is as follows:
3. Loosen the locking handle (f) and push the riving knife (3)
in the upper position (Fig.F)
To Transport The Table Saw (Fig C1, C2)
The upper legs could be locked in the vertical position for
use as a trolley handle.
WARNING! Cover the upper part of the saw blade during
transportation, for example by the guard.
Handle assembly (Fig D)
Place washer (e), housing (b), washer (c) and hex nut (d) on
the bolt (a) to assemble the handle (11)
204
E
C1
B4
2
1
C2
d
c
b
e
a
11
D
Handle assembly (Fig D)
Place washer (e), housing (b), washer (c) and hex nut (d) on
the bolt (a) to assemble the handle (11)
9
ENGLISH