ENGLISH • 9
ASSEMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting sanding sheets (FIG. B y C)
Warning! Never use the tool without a sanding sheet or
accessory in place.
Fitting sanding sheets with nylon loops (FIG. B)
Warning! Make sure that the tool is switched off and
unplugged.
f Press the sheet firmly and evenly onto the sanding
base (4), making sure that the holes in the sheet line
up with the holes in the base.
Fitting regular sanding sheets (FIG. C)
Warning! Make sure that the tool is switched off and
unplugged.
f Soften the sanding sheet by rubbing its non-abrasive
side over the edge of a worktop.
f Press the paper clamp levers (5) upwards to release
them from the retaining grooves and open the paper
clamps (5) by pressing them down.
f Place the sheet onto the sanding base (4).
f Insert the edge of the sanding sheet into the front
paper clamp (5) as shown.
f Press the front paper clamp lever (5) downwards and
locate it in the retaining groove.
f While keeping a slight tension on the sheet, insert the
rear edge of the sheet into the rear paper clamp (5).
f Press the rear paper clamp lever (5) downwards and
locate it in the retaining groove.
Fitting and removing the dustbag (FIG. D)
f Fit the dustbag (2) over the dust extraction outlet (3).
f Slide the dustbag (2) onto the tool and make sure that
it is securely located.
f To remove the dustbag (2), pull it to the rear and off
the outlet.
USE
Warning! Let the tool work at its own pace. Do not
overload.
Switching on and off (FIG. F)
f To switch the tool on, press the part of the on/off
switch (1) marked ‘I’.
f To switch the tool off, press the part of the on/off
switch (1) marked ‘0’.
Emptying the dustbag
f The dustbag (2) should be emptied every 10 minutes.
f Shake the dustbag (2) to empty the contents
Hints for optimum use
f Do not place your hands over the ventilation slots.
f Do not exert too much pressure on the tool.
f Regularly check the condition of the sanding sheet.
Replace when necessary.
f Always sand with the grain of the wood.
f When sanding new layers of paint before applying
another layer, use extra fine grit.
f On very uneven surfaces, or when removing layers of
paint, start with a coarse grit. On other surfaces, start
with a medium grit. In both cases, gradually change to
a fine grit for a smooth finish.
f Consult your retailer for more information on available
accessories.
MAINTENANCE
Your Stanley tool has been designed to operate over
a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
tool care and regular cleaning.
Warning! Before performing any maintenance, switch
off and unplug the tool.
f Regularly clean the ventilation slots in your tool using
a soft dry brush or dry cloth.
f Regularly clean the motor housing using a clean
damp cloth. Do not use any abrasive or solvent-based
cleaner.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Black & Decker
product needs replacement, or if it is of no further
use to you, do not dispose of it with household
waste. Make this product available for separate
collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide for
separate collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.
SERVICE INFORMATION
Black & Decker offers a full network of company-owned and
authorized service locations. All Black & Decker Service
Centers are staffed with trained personnel to provide
customers with efficient and reliable power tool service.
For more information about our authorized service centers
and if you need technical advice, repair, or genuine factory
replacement parts, contact the Black & Decker location
nearest you, or visit us at www.BlackandDecker-la.com
To Next Page
Loading...
