FR
ES
PT
IT
EL
PL
RU
KZ
UA
RO
EN
FR
ES
PT
IT
EL
PL
RU
KZ
UA
RO
EN
242
FR
ES
PT
IT
EL
PL
RU
KZ
UA
RO
EN
WINTERING HOT PRODUCT COLD PRODUCT
BLADE
Remove the spark plu
g
/ Clean it / check if it
needs to be sharpened
Let the product cool
Remove the spark plug
/ Clean it / check if it
needs to be sharpened
SPARK PLUG
Remove it / Brush it /
Plug it
Let the product cool
Remove it / Brush it /
Plug it
AIR FILTER Clean it Clean it Clean it
7. MAINTENANCE
7.1 CLEANING
WARNING! DO NOT HANDLE CUTTING PARTS WITHOUT GLOVES
AS THEY ARE SHARP AND CAN BECOME HOT AFTER USE,
POTENTIALLY CAUSING PERSONAL INJURY.
empty the fuel tank according to the instructions in the engine manual. Ensure not to bend
or damage the cutter when pushing the lawnmower over obstacles. Secure the product to
prevent it from slipping or falling over, damage and injury.
components using a moist, soft cloth. Do not use strong solvents or detergents on the plastic
housing or plastic components. Certain household cleaners may cause damage, and may cause
a shock hazard.
7.2 MAINTENANCE SCHEDULE
WARNING ! REFUEL IN A WELL-VENTILATED AREA WITH THE
ENGINE STOPPED. PLEASE REFER TO THE ENGINE OPERATOR’S
MANUAL FOR THE MAINTENANCE OF THE ENGINE PARTS.
Go Stock Before/After each use Every 10H
FILTERED
VERIFICATION X
CLEANING X
REPLACEMENT EVERY WINTERING
SPARK PLUG
VERIFICATION
CLEANING EVERY WINTERING
REPLACEMENT
WHEN NECESSARY / CONSULT
THE TROUBLESHOOTING GUIDE
OIL LEVEL
VERIFICATION X
FILLING WHEN LEVEL IS LOW
DRAIN EVERY WINTERING
: illustration
5.1
to
5.12
243
FR
ES
PT
IT
EL
PL
RU
KZ
UA
RO
EN
Go Stock Before/After each use Every 10H
BLADE
VERIFICATION X
CLEANING X
REPLACEMENT or
SHARPENING
WHEN NECESSARY / CONSULT
THE TROUBLESHOOTING GUIDE
BLADE HOLDER
VERIFICATION X
CLEANING X
REPLACEMENT
WHEN NECESSARY / CONSULT
THE TROUBLESHOOTING GUIDE
CARTER
VERIFICATION X
CLEANING X
STARTER ROPE
VERIFICATION X
REPLACEMENT
WHEN NECESSARY/ CONSULT
THE TROUBLESHOOTING GUIDE
7.3 REPLACEMENT
WARNING! THE REPLACEMENT OF THE CUTTING DEVICE SHOULD
BE DONE BY AN EXPERIENCED USER! REWORK OR SHARPENING
BLADES IS NOT RECOMMENDED UNLESS IT IS DONE BY A
REPAIRSERVICE OR A SIMILARLY QUALIED SPECIALIST!
When servicing, use only identical replacement parts. Use of any other parts may create a
hazard or cause product damage. If you shall replace the cutting blade, make sure that the
following characteristics are the same: same shape, same length, same thickness, same
weight, same material.
The following part of this product may be replaced by the consumer.:
→ Blade
→ Spare parts are available at an authorized dealer or through our customer service.
Turn the mower onto its side to reveal the underside of the machine. Place a block of wood or a
stop of some kind between the blade and the edge of the deck to prevent the blade from turning
freely. Using a wrench , loosen the blade nut on the bottom of the unit . Remove the blade nut,
the washer, and the blade from the machine.
Put the new blade onto the shaft and replace the blade washer and the blade nut. Tighten the
blade nut. Torque the blade nut to 44-46 N•m. Once the blade is secure, check by hand that
everything rotates as it should.
: illustration
6.6
to
6.12
To Next Page
Loading...
