Need help?Do you have a question about the StetSom BRAVO HQ 800.4 and is the answer not in the manual?
Guidance on correct installation, including safety precautions and connection tips for optimal performance and longevity.
Connect to radio/player outputs using shielded RCA cables for 4 independent channels to prevent unwanted noise.
Use when radio lacks RCA outputs; connects to amplified output signals via REM for remote activation.
Adjusts signal level sent to speakers for equalizing music volume playback.
Allows adjustment of crossover cut-off range from 50Hz to 2.3KHz, working with crossover switches.
Two selection switches (HPF, FLAT, LPF) control frequency cut-off for two channels at a time.
Automatic, variable operation optimizing amplifier ventilation. Requires ventilated installation.
Amplified audio outputs for speaker connection. Check polarity and minimum impedance before installation.
Connect to the battery's positive terminal with a 6 AWG cable and a 40A fuse, placed close to the battery.
Automatic activation with radio/player. Connect to the REMOTE output via a minimum 18 AWG cable.
Connect to the negative battery terminal using a minimum 6 AWG cable.
Indicates the amplifier is operating when lit.
Indicates faults and protection mode. Check protection table for cause and restart amplifier.
Details LED flash patterns for faults like short circuit, overheating, and voltage issues, with corresponding solutions.
Specifies cable sizes (6 AWG, 18 AWG, 13 AWG) and fuse (40A) for proper installation.
Mandatory use of fuse/circuit breaker close to the battery for protection against short circuits and overloads.
Diagram showing connections for HIGH INPUT using blue and gray wires for CH1-CH4.
Illustrates examples for connecting 4x 2 OHMS speakers or 2x speakers with a subwoofer in bridge mode.
Steps to diagnose and resolve issues when the amplifier fails to power on.
Troubleshooting steps for when no audio output is detected, checking connections and level control.
Guidance on interpreting the PROT LED flashes and checking for overheating or short circuits.
How to adjust the LEVEL control to prevent distortion caused by overloaded or defective speakers.
Identifies reversed speaker cables as a cause for lack of bass.
Addresses interference and noise by ensuring installation is away from original vehicle wiring.
Details specific model information including output impedance, channels, and power ratings.
Specifies power output across different impedances and bridge mode at 14.4V supply.
Specifies power output across different impedances and bridge mode at 12.6V supply.
Defines the minimum signal voltage required for RCA and HIGH input connections.
Indicates the audio quality by measuring the difference between signal and noise.
Specifies the range of audio frequencies the amplifier can reproduce.
Defines the adjustable range for low-pass filtering.
Defines the adjustable range for high-pass filtering.
Specifies the boost level available when the switch is in L.P.F. position.
Lists the impedance values for RCA and HIGH input connections.
Specifies the operational voltage range for the amplifier.
Indicates the current drawn during normal music playback.
Indicates the maximum current drawn during bass-heavy playback.
Provides the physical height, width, and length of the amplifier.
States the total weight of the amplifier.
Details the warranty period and requirements for claiming benefits.
Lists conditions and actions that will invalidate the product's warranty.
Provides contact information for customer service and advice regarding products and services.
Declares compliance with EU directives and provides a link to the full text of the declaration.
Lists model specifics: voltage supply, current range, and manufacturing origin.
Explains the EU's WEEE Directive regarding producer obligations for product take-back and recycling.
Guides users on responsible disposal of WEEE, emphasizing designated collection points for recycling.
Field for entering the product's serial number.
Field for recording the date the product was purchased.
Field for recording the month and year the product was manufactured.
Field for reseller information or official stamp.
General| Power Output | 800W RMS |
|---|---|
| Number of Channels | 4 |
| Signal to Noise Ratio | >90dB |
| Crossover | Yes |
| Operating Class | D |
| Minimum Supply Voltage | 9V |
| Maximum Supply Voltage | 16V |
| Maximum Consumption at Musical Signal | 40A |
| Maximum Consumption at Sinusoidal Signal | 80A |
| Input Sensitivity | 0.2V |
| Impedance | 1 OHM |
| Power @ 12.6V @ 1Ω | 800W |
| Power @ 12.6V @ 2Ω | 400W |
| Crossover High Pass (HPF) | 50Hz - 500Hz |
| Crossover Low Pass (LPF) | 50Hz - 500Hz |
| Input Impedance | 10kΩ |
To Next Page
