EasyManua.ls Logo

Stiga A 750 - User Manual

Stiga A 750
79 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
A 500
A 750
A 1000
A 1500
A 3000
A 5000
A 7500
A 10000
EN Instruction manual

Table of Contents

Questions and Answers

  • M
    Mckenzie HillAug 10, 2025
    Why is my Stiga A 750 Lawn Mower vibrating abnormally and noisy?
    • K
      Keith Dean DDSAug 10, 2025
      Abnormal vibrations and noise in your Stiga Lawn Mower can stem from several causes. The cutting disc or blades might be damaged, requiring replacement. Residues like tapes or plastic fragments may be blocking the cutting device, so switch off the mower in safety conditions and unlock the cutting blade. Unexpected obstacles, such as fallen branches, could also be the culprit; remove them and restart the mower. If the grass is too tall, increase the cutting height. In rare cases, it may be an electric motor failure, in which case you should replace the motor contacting the nearest authorized service centre. If all of these are not the case, make a preliminary cut of the area with a normal lawn mower.
  • N
    Nicholas OrozcoAug 30, 2025
    How to fix Stiga A 750 Lawn Mower not positioning correctly in the charging station?
    • B
      Bonnie BennettAug 30, 2025
      If your Stiga Lawn Mower isn't positioning correctly in the charging station, it could be due to land subsidence near the charging base; restore the correct positioning of the charging base. There may be a problem with the charging base antenna, if the problem persists, contact a service centre. Alternatively, the charging base may not be calibrated correctly, or electromagnetic interferences might be present; after eliminating the source of disturbance, calibrate the charging base through the app.
  • K
    Katherine WilsonNov 18, 2025
    What to do if my Stiga A 750 Lawn Mower isn't mowing the entire area?
    • J
      jennifer50Nov 18, 2025
      If your Stiga Lawn Mower isn't completely mowing the working area, several factors could be responsible. Insufficient working hours may be the issue, so extend the working hours. The cutting device might have encrustations or residues, requiring you to switch off the mower in safety conditions and clean the cutting device. Pivoting cutting blades blocked by encrustations or residues could also be the cause, so switch off the mower in safety conditions and replace the cutting blades. The working area may be too large for the mower's capacity, consider reducing the work area. Batteries may be near the end of their life cycle, replace the batteries with original spare parts. Finally, the batteries might not be fully charged, clean and eliminate any oxidation from the contact points and rechar...

Summary

Models and Technical Data

1.2. Technical Data

Safety

2.1. Safety Information

General safety warnings and precautions for using the robot lawn mower safely.

2.2.1. Safe Operating Procedures

Guidelines for safe operation, training, and preparation for using the robot mower.

2.2.2. Operation

2.3. Stopping and Turning Off the Robot Lawn Mower in Safe Conditions

Procedure for safely stopping and switching off the robot lawn mower.

Installation

4.3.1. Garden Verification

4.3.2. Checks for the Installation of the Charging Base and Power Supply

Safety checks and requirements for installing the charging base and power supply.

4.3.3. Checks to Define the Virtual Perimeters

Rules and diagrams for setting virtual boundaries based on garden slope.

4.4.1. Minimum Virtual Boundaries and Delimitation Distances

Guidelines for setting virtual boundaries around obstacles and garden features.

4.5.1. Installation of the Charging Base

Step-by-step guide for securely installing the charging base.

4.5.2. Installing the Satellite Reference Station

Instructions for correctly installing the satellite reference station for navigation.

4.6. Programming Virtual Perimeters, Transition Routes and Areas to be Avoided

Overview of programming garden boundaries and no-go zones using the STIGA.GO App.

4.7.3. Device Pairing

4.7.7. Calibration of the Charging Base

Procedure for calibrating the charging base for accurate return to the docking station.

4.7.8. Initialization of the Robot Lawn Mower

4.7.9. Programming Virtual Perimeters, Transition Routes and Areas to be Avoided

Detailed steps for programming virtual boundaries using the STIGA.GO App.

4.7.10. Programming the Return Route to the Charging Base

4.7.20. Firmware Update

4.7.22. Anti-Theft Alarm

Operation

5.1. Check of Safety Devices for Starting the Robot Lawn Mower

Ensures all safety devices are functional before starting the robot lawn mower.

5.3. Description of the Controls on the Robot Lawn Mower

5.3.1. Safe Stop - Stop Button

5.3.2. Safe Shutdown - Safety Key

Describes how to safely shut down the mower using the safety key.

5.3.3. Switching the Robot Lawn Mower On and Off - ON;OFF Button

5.3.4. Scheduled Programme Selection; Single Work Cycle; Forced Return to Charging Base - Mode Selection Button

5.3.6. Display of Alarm States-Alarm Icon

How to interpret and reset alarm states indicated by the alarm icon.

5.3.8. Starting the Robot Lawn Mower

5.5. Battery Charging

Maintenance

6.1. Scheduled Maintenance

Outlines regular maintenance tasks for the robot mower, including frequency.

6.2. Product Cleaning

6.3. Replacement of the Cutting Blades

Step-by-step guide for safely replacing the cutting blades on the robot mower.

6.4. Winter Battery Maintenance and Storage

Troubleshooting

Transport, Storage and Disposal

Warranty

10.1. Warranty Coverage

Stiga A 750 Specifications

General IconGeneral
BrandStiga
ModelA 750
CategoryLawn Mower
LanguageEnglish

Related product manuals