To Next PageTo Next PageHow to prevent grass accumulation on my Stiga LT 20 Li S?
Grass accumulation around the power unit housing and cutting line head of your Stiga Trimmer is often caused by cutting grass that is too high close to the ground. To prevent this, cut tall grass with a top-down movement.
What to do if my Stiga LT 20 Li S Trimmer cutting head is stationary?
If the cutting head of your Stiga Trimmer is stationary, and the machine doesn't start when engaged, possible causes include: the battery not being properly inserted (ensure it's well-inserted), a low battery (check its status and recharge if needed), a defective throttle control lever/throttle safety lever (in which case, stop using the machine, remove the battery, and contact an authorized service dealer), or the machine being damaged (also requiring you to stop use, remove the battery, and contact a dealer).
Why is my Stiga Trimmer giving off smoke?
If your Stiga Trimmer is emitting smoke while in operation, this could be due to machine damage (in which case, stop using the machine, remove the battery, and contact an authorized service dealer), severe working conditions requiring greater current absorption (optimize operations), or the battery being insufficient for operating requirements (use a second or extended battery).
Why does my Stiga LT 20 Li S Trimmer vibrate so much?
Excessive noise and vibration in your Stiga Trimmer usually indicates loose or damaged parts. To address this, turn off the machine, remove the battery, inspect for damage, tighten any loose parts, and have any replacements or repairs done by an authorized service dealer.
What to do if the line is not released on my Stiga Trimmer?
If the line isn't releasing automatically on your Stiga Trimmer, it could be stuck to itself (lubricate with silicone spray), there might not be enough line on the reel or the reel is empty (replace the reel or the line), the line could be worn and too short, or the line is tangled or broken on the reel (remove the line from the reel and rewind it).
How to fix a Stiga LT 20 Li S Trimmer battery charger that is not recharging?
If your Stiga Trimmer's battery charger isn't recharging the battery, check if the battery is correctly inserted. Ensure suitable environmental conditions for recharging. Clean the contacts and verify the charger is plugged in and the power socket is energized. If the charger is faulty, replace it with an original spare part.
Why is my Stiga LT 20 Li S motor overheating?
If your Stiga Trimmer's motor is overheating, it may be due to grass caught under the cutting means guard. Remove any grass that is caught.
What to do if Stiga Trimmer cutting head hits something?
If the cutting head of your Stiga Trimmer comes into contact with a foreign object, turn off the machine and remove the battery. Then, inspect the trimmer for damage, check for and tighten any loose parts, and have any necessary replacements or repairs carried out by an authorized service dealer.
General| Power Source | Battery |
|---|---|
| Battery Voltage | 20 V |
| Battery Type | Lithium-Ion |
| Cutting Width | 30 cm |
| Weight | 2.4 kg |
| Handle Type | Loop handle |
| Shaft Type | Telescopic |
| Adjustable Cutting Height | Yes |
Guidance on interpreting manual symbols and important notes for safe operation.
Essential safety rules, training, preparation, operation, residual risks, and environmental guidelines.
Overview of the machine, its parts, intended use, identification, and safety signs.
Steps for unpacking and fitting machine parts like grips, guards, and indicators.
Explanation of throttle and safety lever functions for machine operation.
Preparation, start-up, work techniques, advice, stopping, and after-use procedures.
Essential safety rules and general information before performing maintenance.
Procedures for battery, cleaning, cutting head, and sharpening the line knife.
Instructions for safe storage of the machine and its battery.
Key technical data including voltage, speed, cutting width, and noise levels.
Common problems, solutions, assistance, warranty, and accessories information.
Instructions for safe handling and transportation of the machine.
