6.
CD OPERATION
To Cancel Repeat/Shuffle Function: Tap the REPEAT BUTTON repeatedly until
REPEAT/SHUFFLE indicator goes off from LCD display.
PROGRAM OPERATION
This function allows the tracks to be played in a programmed sequence.
NOTE: Programs can only be set in STOP mode.
PLEASE READ THIS IMPORTANT INFORMATION:
CD mechanisms used in devices like this are designed to fully read all commercial CDs.
They will also read self-compiled CD-R/CD-RW discs, but it may take up to 10 seconds for
playback to start. If playback does not start, it is likely due to the quality of the CD-R/RW
disc and/or the compatibility of the CD compilation software. The manufacturer is not
responsible for the playback quality of CD-R/RW discs.
Do not attach a label or seal to either side of the CD-R/RW disc. It may cause a malfunction.
1. In CD stop mode, press and hold the MEM/M+ button, the PROGRAM indicator “MEM”
will flash and Program Number “P01” will show on LCD display.
Press the SKIP or button to select the desired track. The track number “001”
will blink on the LCD display to prompt for input.
2.
“FUL” to indicate the program is full.
When
playing.
you
Both
have
PROGRAM
completed
(MEM)
programming,
and
pre
PLAY/PAUSE
ss the
(
PLAY/PAUSE button to start
) indicators will light steadily.
button twice. PROGRAM indicator 7. To cancel programmed play, press the STOP
5. Press the PLAY/PAUSE button to start playing.
“MEM” will then no longer show on the LCD display.
6.
7.
Rotate the VOLUME knob to obtain the desired sound.
To temporarily stop playing, press the PLAY/PAUSE Button. The play/pause indicator
USB OPERATION
“ ” on the LCD display will begin to flash. To resume playing, press the PLAY/PAUSE
This unit is designed to play MP3 files stored within the USB flash-drives. If the files on the
USB device do not conform to the MP3 standard, they may not be played.
Button again. The play/pause indicator “ “ will turn to solid on.
8. You can skip up or down to a specific track number by pressing the SKIP BACKWARD
button or SKIP FORWARD button. The LCD Display
track number selected.
To locate a particular section within a track, press and hold the
the section is found.
will indicate the correct
9. / button until
+10 button control
Press the +10 button once to advance the music search by increment of 10 tracks.
REPEAT MODE
Repeat 1
To repeat the current track, press the REPEAT BUTTON (BUTTON 8) once, the REPEAT
USB Playback
After reading the USB flash-drive, press the PLAY/PAUSE button once, the first track/file
on the USB flash-drive will be played back. The PLAY/PAUSE indicator “
during playback.
” will be solid on
INDICATOR will begin to flash on the LCD display. The track will continue to play until
Play/Pause Control
To temporarily stop playing, press the
the repeat function is turned off by pressing the REPEAT BUTTON again.
Repeat All
To repeat all the tracks, press the REPEAT BUTTON twice, the REPEAT INDICATOR
will be solid on. All the tracks on the disc will be played repeatedly.
REPEAT FOLDER
When playing a MP3 CD, tap the REPEAT BUTTON repeatedly until the REPEAT
FOLDER indicator appears on the LCD DISPLAY, allowing you to repeat songs in the
folder.
SHUFFLE TRACKS
To shuffle all tracks in the CD, tap the REPEAT BUTTON repeatedly until the SHUFFLE
button, music playback will be paused, and the
PLAY/PAUSE indicator “ ” will be blinking. Press the button again to resume playback.
Stop Playback
To stop playback, press the STOP
button on the unit. The total number of tracks/files on
the USB flash-drive will be shown on the LCD display.
Skip Track
During playback, press the SKIP backward
previous or next track/file.
or forward buttons to skip to the
High-speed Music Search
During playback, press and hold the SKIP forward or backward buttons to search
through the current track/file at high speed in forward or backward directions. When the SKIP
indictor appears on the LCD display. All the tracks on the disc will be played randomly.
9 10
1. In power on mode, tap the MODE button repeatedly to select CD mode, the display will
show “- - -“ briefly. If no CD has been loaded in the CD compartment, LCD display will
change to show “
no”.
2. Open the CD door by lifting it up.
3. Carefully load an audio CD with its label side upward in the CD compartment then
lower the CD door down to close it.
4. The player will start reading TOC of the disc, total number of tracks on the CD will
appear on the LCD DISPLAY after a few seconds.
3. Tap the MEM button to confirm the selection. Program Number advances to “P02”.
4. Repeat step 2 to 3 to program up to maximum of 30 tracks.
5. When a maximum of 30 tracks have been programmed, the LCD display will show
1. Press and hold the POWER
button to turn on the unit. Tap the MODE button
repeatedly until USB mode indication “USB” shows on LCD display.
2. Insert your USB flash-drive into the USB port located at back of the unit, it will start to
read the USB flash-drive.
Note: USB supports flash drive capacity up to 64 GB maximum.
3. After reading the USB flash-drive, the unit will display the total number of tracks/files in
the flash-drive.
10. To stop playing, press the STOP button.
11. Press and hold the POWER button to turn off the unit after listening.
To Next Page
Loading...
