32
Features of your Maestro Kettle
3-Way Safety System.
1 – Automatically switches the kettle off after boiling.
2 – Cuts out for boil-dry production.
3 – Shuts down in case of overheating.
1.7L brushed stainless
steel design
7 cup capacity kettle
constructed using long
life stainless steel.
2400 watt concealed
element
The fast boil 2400 watt
element is concealed in
the base of the kettle for
longer element life.
360 degree cordless
power base
Designed to allow you to
place the kettle on the
base in any direction.
Removable mesh filter
Keeps the water clean of
any foreign matter and is
removable for easy
cleaning.
Viewing Window
Clear window in the
kettle lid can be used
to check boiling
progress.
Hinged locking lid
Opens at the push of a
button for one-handed
use and easy filling at
the tap.
Rear water level gauge
Full length water gauge
indicates the volume of
water in the kettle up
to 1.7L.
On/Off switch with auto
cut-off
Switches the kettle off
automatically after
boiling.
Cord storage facility
Excess cord can be
wound around the cord
storage facility
underneath the power
base.
Safety is a major consideration in the
design of a Sunbeam kettle. This is why we
have developed our 3-Way Safety System,
which ensures that your kettle will:
1. Automatically switch off after boiling.
For convenience, safety and energy
efficiency, your Sunbeam kettle will
automatically switch off after boiling.
2. Cut-out for boil-dry protection.
If the kettle is operated without water, it
will automatically cut-out,
preventing any damage to the
element.
If this occurs, allow the kettle to cool before
filling with cold water and re-boiling.
3. Shut-down in case of overheating.
In the event of overheating, the kettle will
automatically shut down to prevent further
damage. Should this occur, take your kettle
to a Sunbeam Service Centre or Appointed
Service Agent.
Before using your kettle.
It is recommended that you clean your kettle
before use by filling the kettle with water, up to
the maximum level indicator, boil and discard.
Using your kettle.
1. To fill the kettle, remove it from the power
base and lift the lid, by pressing the button
on the handle. Alternatively, the kettle may
be filled through the pouring spout.
2. Fill the kettle with the desired amount of
water. Always fill the kettle between the
minimum and maximum marks. Too little
water will result in the kettle switching off
before the water has boiled.
NOTE: Do not fill the kettle over the maximum
level, as water may spill out of the spout
when boiling.
3. Push the lid closed firmly until it locks into
position.
4. Place the kettle on the power base and
connect the plug into a 230/240 Volt AC
power outlet. Turn the power ON.
5. Press the ON/OFF button downwards at the
base of the kettle. The ON/OFF button will
illuminate to indicate the kettle is heating.
The kettle will switch off automatically
once the water has boiled.
NOTE: Ensure that the ON/OFF switch is clear
of obstructions and the lid is firmly closed.
The kettle will not turn off if the ON/OFF
switch is constrained or if the lid is left open.
Do not remove the kettle from the power base
while water is heating.
6. Lift the kettle from the power base and
pour the water.
NOTE: Use caution when pouring the water
from your kettle, as boiling water will scald.
7. The kettle may be stored on the power base
while not in use. The kettle will not re-boil
until the ON/OFF switch is pressed downward.
NOTE: Ensure the power is turned off at the
power outlet when the kettle is not in use.
Should you accidentally allow the kettle to
operate without water, boil-dry protection will
automatically switch it off. If this occurs,
allow the kettle to cool before filling with
cold water and re-boiling.
Cord Storage Facility.
Excess cord can be stored by winding the
cord around the storage facility underneath
the power base.
Using your Maestro Kettle
Sunbeam’s 3-Way Safety System
To Next Page