To Next PageTo Next Page
Need help?Do you have a question about the sunjoe GTS4002C and is the answer not in the manual?
Follow basic safety precautions to reduce the risk of fire, electric shock, and personal injury.
Keep work area clean and well-lit; avoid dangerous environments and keep spectators away.
Dress properly, stay alert, use two hands, and wear safety glasses and head protection.
Never use the power tool near electrical power lines; maintain 50 ft clearance.
Use two hands, keep clear of objects, never stand under limbs, and cut limbs carefully.
Avoid guide bar tip contact; use two hands, keep guards in place, maintain footing and balance.
Remove keys before starting; ensure blades are correctly fastened; do not cut stems over 0.6 in.
Use only approved batteries; do not use damaged packs; handle with care.
Do not crush, drop, burn, or short circuit battery packs; handle chemicals safely.
Maintain charger cord; use correct extension cords; unplug when not in use.
Read manual, wear eye/hearing protection, use gloves, and wear foot protection.
Do not expose to rain, beware of shock hazard, and keep bystanders clear.
Danger of rotating blades, thrown objects, and beware of thrown objects to bystanders.
Use only compatible charger; avoid water near plugs; charger does not auto-shutoff.
Never allow battery pack to fully discharge to prevent irreversible damage.
DANGER: Never start motor before installing guide bar, chain, and cover.
Remove hex bolt, end cover; remove old chain; orient new chain correctly; mount chain to bar.
Release buttons to set angle; ensure head is securely locked to prevent injury.
Avoid wet conditions; do not cut tensioned limbs; never cut near electrical wires; lubricate chain.
Check cold chain tension; re-tension warm chain; sharpen when cutting is difficult or noisy.
Most issues are fixable; remove battery before adjustments; contact service for complex problems.
Common issues like motor failure, low chain speed, hot bar/chain, or no chain movement.
Align and firmly press safety guard into head until it clicks; provides protection from thrown objects.
Clear area of debris; hold trimmer away from body; stop immediately if blades jam.
Check battery, clean spool/slots; trim line to blade; take to service center if issues persist.
Hold with both hands; clear area of objects; do not force through dense growth; trim stems up to 0.6 in.
Wear gloves when handling blades; lubricate blades before/after use with machine oil.
Follow basic safety precautions to reduce the risk of fire, electric shock, and personal injury.
Keep work area clean and well-lit; avoid dangerous environments and keep spectators away.
Dress properly, stay alert, use two hands, and wear safety glasses and head protection.
Never use the power tool near electrical power lines; maintain 50 ft clearance.
Use two hands, keep clear of objects, never stand under limbs, and cut limbs carefully.
Avoid guide bar tip contact; use two hands, keep guards in place, maintain footing and balance.
Remove keys before starting; ensure blades are correctly fastened; do not cut stems over 0.6 in.
Use only approved batteries; do not use damaged packs; handle with care.
Do not crush, drop, burn, or short circuit battery packs; handle chemicals safely.
Maintain charger cord; use correct extension cords; unplug when not in use.
Read manual, wear eye/hearing protection, use gloves, and wear foot protection.
Do not expose to rain, beware of shock hazard, and keep bystanders clear.
Danger of rotating blades, thrown objects, and beware of thrown objects to bystanders.
Use only compatible charger; avoid water near plugs; charger does not auto-shutoff.
Never allow battery pack to fully discharge to prevent irreversible damage.
DANGER: Never start motor before installing guide bar, chain, and cover.
Remove hex bolt, end cover; remove old chain; orient new chain correctly; mount chain to bar.
Release buttons to set angle; ensure head is securely locked to prevent injury.
Avoid wet conditions; do not cut tensioned limbs; never cut near electrical wires; lubricate chain.
Check cold chain tension; re-tension warm chain; sharpen when cutting is difficult or noisy.
Most issues are fixable; remove battery before adjustments; contact service for complex problems.
Common issues like motor failure, low chain speed, hot bar/chain, or no chain movement.
Align and firmly press safety guard into head until it clicks; provides protection from thrown objects.
Clear area of debris; hold trimmer away from body; stop immediately if blades jam.
Check battery, clean spool/slots; trim line to blade; take to service center if issues persist.
Hold with both hands; clear area of objects; do not force through dense growth; trim stems up to 0.6 in.
Wear gloves when handling blades; lubricate blades before/after use with machine oil.
General| Power Source | Battery |
|---|---|
| Tines | 4 Steel Tines |
| Weight | 22.9 lb (10.4 kg) |
| Handle | Adjustable |
| Warranty | 2-Year |
| Tilling Depth | 8 inches |
