To Next PageTo Next PageWhat to do if sunjoe Lawn and Garden Equipment grass trimmer + edger does not start?
If your Sun Joe Lawn and Garden Equipment grass trimmer + edger doesn't start, first check if the safety switch has been activated. Also, make sure you're using a functional extension cord. If it still doesn't start after these checks, take it to an authorized service center.
General safety precautions for operating the electric grass trimmer + edger.
Detailed steps for installing and changing the SharperBlade™ trimmer blade.
Guidance and technique for trimming grass and edges effectively.
Procedures for cleaning and maintaining the grass trimmer and edger.
Common problems and their possible solutions for the trimmer and edger.
General safety precautions for operating the electric grass trimmer + edger.
Detailed steps for installing and changing the SharperBlade™ trimmer blade.
Guidance and technique for trimming grass and edges effectively.
Procedures for cleaning and maintaining the grass trimmer and edger.
Common problems and their possible solutions for the trimmer and edger.
The Snow Joe® + Sun Joe® Electric SharperBlade™ Trimmer + Edger, Model SB601E, is a versatile outdoor power tool designed for maintaining lawns and trimming along the borders of flower beds. This double-insulated appliance is intended for outdoor use only, within an ambient temperature range of 32°F (0°C) to 113°F (45°C). Its primary function is to cut grass and weeds in areas that conventional lawn mowers cannot reach, such as under bushes, on slopes, and along edges.
The device operates as both a grass trimmer and an edger, offering a 2-in-1 functionality. It utilizes a unique SharperBlade™ trimmer blade, which is more rigid than traditional string lines, for efficient cutting. The tool is activated by an ON/OFF trigger switch, preceded by pressing a safety lock button to prevent unintentional starting.
As a trimmer, the device is used for general grass and weed cutting. The operator holds the trimmer head above the ground, allowing only the SharperBlade™ to make contact with the vegetation. The manual advises against forcing the blade into the work area. For areas inaccessible to lawn mowers, the tool can be used in a mowing position, keeping the SharperBlade™ parallel to the ground. Scalping, a technique to remove unwanted vegetation down to the ground, involves holding the trimmer head about 3 inches (8 cm) above the ground at an angle, allowing the blade tip to strike the ground around obstacles like trees and posts. This technique, however, increases SharperBlade™ wear.
To convert the trimmer into an edger, the Twist-N-Groom™ locking collar is slid downward, and the handle is twisted clockwise to adjust the trimmer head to a 180° angle. This allows the tool to be used for precise edging along pathways and garden beds. To revert to the trimming function, the locking collar is slid downward, and the handle is twisted counterclockwise to return the head to a 0° angle.
The device also features a sweeping function, where fanning action can be used for quick and easy clean-up. This involves keeping the SharperBlade™ parallel to and above the surfaces being swept and moving the tool from side to side.
The trimmer + edger is designed with user comfort and safety in mind. It includes an adjustable auxiliary handle that can be set to the most comfortable position for the operator. The telescopic shaft is also adjustable, allowing users to customize the tool's height for optimal balance and footing during operation.
Safety is paramount, with several features and instructions aimed at preventing injury. The device comes with a safety guard that must be properly installed to provide partial protection from thrown objects. Operators are instructed to wear suitable clothing, including safety glasses, safety footwear, snug-fitting clothing, protective gloves, and hearing and head protection. Children and bystanders, including pets, must be kept at least 50 feet (15 meters) away from the work area due to the risk of flying projectiles.
The manual emphasizes using minimal pressure when edging against hard surfaces like concrete, brick, or stone to prolong the blade's life. The secret is to keep the blade just off the hard surface rather than pressing it firmly. Operators are also advised never to force the SharperBlade™, as high speed and impact against hard surfaces can cause the blade to buckle or tear. Instead, the tool should be allowed to do the work without extra effort.
For electrical safety, the device requires a polarized extension cord suitable for outdoor, all-weather use. Ground fault circuit interrupter (GFCI) protection is recommended. The manual provides detailed instructions on how to secure the extension cord to prevent accidental disconnection during operation. It also warns against using the tool in damp or wet locations, in rain, or touching the appliance or its plug with wet hands.
Proper maintenance is crucial for the efficiency and longevity of the electric grass trimmer + edger. Before any maintenance task, the tool must be disconnected from the power supply. Operators are advised to wear protective gloves during maintenance and avoid performing tasks when the engine is running or hot.
Regular cleaning is essential. After each cutting operation, grass and soil should be removed from the entire trimmer + edger and its guard. The air vents must be kept clean and free from grass during operation. For cleaning, only a cloth soaked with hot water and a soft brush should be used; detergents or solvents are not recommended as they can damage plastic parts. The appliance should not be sprayed or wetted with water.
The SharperBlade™ trimmer blade is a consumable part. If it no longer cuts or breaks, it should be replaced by contacting an authorized service center. The manual explicitly warns against using steel blades, wire, string, rope, or other non-original materials, as they can break off during cutting and become dangerous projectiles.
For storage, the trimmer + edger should be thoroughly cleaned and stored indoors in a dry, high, or locked-up place, out of reach of children. It should not be stored resting against the floor; instead, it should be hung by the upper handgrip to prevent the guard from touching any surface, which could alter its shape and dimensions, rendering the machine unsafe.
Troubleshooting guidance is provided for common issues like vibration or the device not starting. For vibration, the SharperBlade™ should be removed and cleaned, and if vibration persists, the blade should be replaced. If the problem continues, an authorized service center should be contacted. For starting issues, electrical connections should be checked, and the safety circuit-breaker and electrical system fuse should be inspected. If these checks do not resolve the issue, the tool should be taken to an authorized service center.
General| Weight | 8.6 lbs |
|---|---|
| Voltage | 120V |
| Air Speed | 250 mph |
| Air Volume | 495 cfm |
| Warranty | Two years |
